- 您現在的位置：買賣IC網 > PDF目錄4497 > A54SX08A-TQ144I (Microsemi SoC)IC FPGA SX 12K GATES 144-TQFP PDF資料下載
參數資料
| 型號： | A54SX08A-TQ144I |
| 廠商： | Microsemi SoC |
| 文件頁數： | 16/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA SX 12K GATES 144-TQFP |
| 標準包裝： | 60 |
| 系列： | SX-A |
| LAB/CLB數： | 768 |
| 輸入/輸出數： | 113 |
| 門數： | 12000 |
| 電源電壓： | 2.25 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-TQFP（20x20） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
SX-A Family FPGAs
v5.3
1-11
Probing Capabilities
SX-A devices also provide an internal probing capability
that is accessed with the JTAG pins. The Silicon Explorer II
diagnostic hardware is used to control the TDI, TCK, TMS,
and TDO pins to select the desired nets for debugging.
The user assigns the selected internal nets in Actel Silicon
Explorer II software to the PRA/PRB output pins for
observation. Silicon Explorer II automatically places the
device into JTAG mode. However, probing functionality is
only activated when the TRST pin is driven high or left
floating, allowing the internal pull-up resistor to pull
TRST High. If the TRST pin is held Low, the TAP controller
remains in the Test-Logic-Reset state so no probing can
be performed. However, the user must drive the TRST pin
High or allow the internal pull-up resistor to pull TRST
High.
When selecting the Reserve Probe Pin box as shown in
Figure 1-12 on page 1-9, direct the layout tool to reserve
the PRA and PRB pins as dedicated outputs for probing.
This Reserve option is merely a guideline. If the designer
assigns user I/Os to the PRA and PRB pins and selects the
Reserve
Probe
Pin option, Designer Layout will
override the Reserve Probe Pin option and place the
user I/Os on those pins.
To allow probing capabilities, the security fuse must not
be programmed. Programming the security fuse disables
the JTAG and probe circuitry. Table 1-9 summarizes the
possible device configurations for probing once the
device leaves the Test-Logic-Reset JTAG state.
Table 1-9 Device Configuration Options for Probe Capability (TRST Pin Reserved)
JTAG Mode
TRST1
Security Fuse Programmed
PRA, PRB2
TDI, TCK, TDO2
Dedicated
Low
No
User I/O3
JTAG Disabled
High
No
Probe Circuit Outputs
JTAG I/O
Flexible
Low
No
User I/O3
High
No
Probe Circuit Outputs
JTAG I/O
Yes
Probe Circuit Secured
Notes:
1. If the TRST pin is not reserved, the device behaves according to TRST = High as described in the table.
2. Avoid using the TDI, TCK, TDO, PRA, and PRB pins as input or bidirectional ports. Since these pins are active during probing, input
signals will not pass through these pins and may cause contention.
3. If no user signal is assigned to these pins, they will behave as unused I/Os in this mode. Unused pins are automatically tristated by
the Designer software.
相關PDF資料 |
PDF描述 |
|---|---|
| A54SX08A-1TQ144 | IC FPGA SX 12K GATES 144-TQFP |
| HSM44DRYS | CONN EDGECARD 88POS DIP .156 SLD |
| A54SX08A-TQG144I | IC FPGA SX 12K GATES 144-TQFP |
| A54SX08A-1TQG144 | IC FPGA SX 12K GATES 144-TQFP |
| HMM44DRYS | CONN EDGECARD 88POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A54SX08A-TQ208 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs |
| A54SX08A-TQ208A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs |
| A54SX08A-TQ208B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs |
| A54SX08A-TQ208I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs |
| A54SX08A-TQ208M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs |
發布緊急采購，3分鐘左右您將得到回復。