- 您現在的位置：買賣IC網 > PDF目錄19343 > A54SX16A-TQG100 (Microsemi SoC)IC FPGA 180I/O 100TQFP PDF資料下載
參數資料
| 型號： | A54SX16A-TQG100 |
| 廠商： | Microsemi SoC |
| 文件頁數： | 14/108頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA 180I/O 100TQFP |
| 標準包裝： | 90 |
| 系列： | SX-A |
| LAB/CLB數： | 1452 |
| 輸入/輸出數： | 81 |
| 門數： | 24000 |
| 電源電壓： | 2.25 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 其它名稱： | 1100-1067 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
SX-A Family FPGAs
v5.3
1-9
Boundary-Scan Testing (BST)
All SX-A devices are IEEE 1149.1 compliant and offer
superior diagnostic and testing capabilities by providing
Boundary Scan Testing (BST) and probing capabilities.
The BST function is controlled through the special JTAG
pins (TMS, TDI, TCK, TDO, and TRST). The functionality of
the JTAG pins is defined by two available modes:
Dedicated and Flexible. TMS cannot be employed as a
user I/O in either mode.
Dedicated Mode
In Dedicated mode, all JTAG pins are reserved for BST;
designers cannot use them as regular I/Os. An internal
pull-up resistor is automatically enabled on both TMS
and TDI pins, and the TMS pin will function as defined in
the IEEE 1149.1 (JTAG) specification.
To select Dedicated mode, the user must reserve the
JTAG pins in Actel’s Designer software. Reserve the JTAG
pins by checking the Reserve JTAG box in the Device
Selection Wizard (Figure 1-12).
The default for the software is Flexible mode; all boxes
are unchecked. Table 1-5 lists the definitions of the
options in the Device Selection Wizard.
Flexible Mode
In Flexible mode, TDI, TCK, and TDO may be employed as
either user I/Os or as JTAG input pins. The internal
resistors on the TMS and TDI pins are not present in
flexible JTAG mode.
To select the Flexible mode, uncheck the Reserve JTAG
box in the Device Selection Wizard dialog in the Actel
Designer software. In Flexible mode, TDI, TCK, and TDO
pins may function as user I/Os or BST pins. The
functionality is controlled by the BST Test Access Port
(TAP) controller. The TAP controller receives two control
inputs, TMS and TCK. Upon power-up, the TAP controller
enters the Test-Logic-Reset state. In this state, TDI, TCK,
and TDO function as user I/Os. The TDI, TCK, and TDO are
transformed from user I/Os into BST pins when a rising
edge on TCK is detected while TMS is at logic low. To
return to Test-Logic Reset state, TMS must be high for at
least five TCK cycles. An external 10 k pull-up resistor
to VCCI should be placed on the TMS pin to pull it
High by default.
describes
the
different
configuration
requirements of BST pins and their functionality in
different modes.
TRST Pin
The TRST pin functions as a dedicated Boundary-Scan
Reset pin when the Reserve JTAG Test Reset option is
selected as shown in Figure 1-12. An internal pull-up
resistor is permanently enabled on the TRST pin in this
mode. Actel recommends connecting this pin to ground
in normal operation to keep the JTAG state controller in
the Test-Logic-Reset state. When JTAG is being used, it
can be left floating or can be driven high.
When the Reserve JTAG Test Reset option is not
selected, this pin will function as a regular I/O. If unused
as an I/O in the design, it will be configured as a tristated
output.
Figure 1-12 Device Selection Wizard
Table 1-5 Reserve Pin Definitions
Pin
Function
Reserve JTAG
Keeps pins from being used and
changes the behavior of JTAG pins (no
pull-up on TMS)
Reserve
JTAG
Test
Reset
Regular I/O or JTAG reset with an
internal pull-up
Reserve Probe
Keeps pins from being used or regular
I/O
Table 1-6 Boundary-Scan Pin Configurations and
Functions
Mode
Designer
"Reserve JTAG"
Selection
TAP Controller
State
Dedicated (JTAG)
Checked
Any
Flexible (User I/O)
Unchecked
Test-Logic-Reset
Flexible (JTAG)
Unchecked
Any EXCEPT Test-
Logic-Reset
相關PDF資料 |
PDF描述 |
|---|---|
| A40MX04-VQG80 | IC FPGA 69I/O 80VQFP |
| R24P215S/P/R6.4 | CONV DC/DC 2W 24VIN 15VOUT |
| GEM18DCAN-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| RSO-2409DZ/H2 | CONV DC/DC 1W 9-36VIN +/-09VOUT |
| TAJY477K002RNJ | CAP TANT 470UF 2.5V 10% 2917 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A54SX16A-TQG100A | 功能描述:IC FPGA SX 24K GATES 100-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:SX-A 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17） |
| A54SX16A-TQG100I | 功能描述:IC FPGA SX 24K GATES 100-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:SX-A 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17） |
| A54SX16A-TQG100M | 制造商:Microsemi Corporation 功能描述:FPGA SX-A Family 16K Gates 924 Cells 227MHz 0.25um Technology 2.5V 100-Pin TQFP 制造商:Microsemi Corporation 功能描述:FPGA SX-A 16K GATES 924 CELLS 227MHZ 0.25UM/0.22UM 2.5V 100T - Trays |
| A54SX16A-TQG144 | 功能描述:IC FPGA 180I/O 144TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:SX-A 標準包裝:24 系列:ECP2 LAB/CLB數:1500 邏輯元件/單元數:12000 RAM 位總計:226304 輸入/輸出數:131 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP（28x28） |
| A54SX16A-TQG144A | 功能描述:IC FPGA SX 24K GATES 144-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:SX-A 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA（17x17） |
發(fā)布緊急采購，3分鐘左右您將得到回復。