- 您現在的位置：買賣IC網 > PDF目錄1890 > AD5235BRU25-RL7 (Analog Devices Inc)IC DGTL POT DUAL 1024POS 16TSSOP PDF資料下載
參數資料
| 型號： | AD5235BRU25-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT DUAL 1024POS 16TSSOP |
| 標準包裝： | 1 |
| 接片： | 1024 |
| 電阻（歐姆）： | 25k |
| 電路數： | 2 |
| 溫度系數： | 標準值 35 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 3 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | AD5235BRU25-RL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD5235
Data Sheet
Rev. F | Page 16 of 32
THEORY OF OPERATION
The AD5235 digital potentiometer is designed to operate as a
true variable resistor. The resistor wiper position is determined
by the RDAC register contents. The RDAC register acts as a
scratchpad register, allowing unlimited changes of resistance
settings. The scratchpad register can be programmed with any
position setting using the standard SPI serial interface by loading
the 24-bit data-word. In the format of the data-word, the first four
bits are commands, the following four bits are addresses, and the
last 16 bits are data. When a specified value is set, this value can
be stored in a corresponding EEMEM register. During subsequent
power-ups, the wiper setting is automatically loaded to that value.
Storing data to the EEMEM register takes about 15 ms and
consumes approximately 2 mA. During this time, the shift
register is locked, preventing any changes from taking place.
The RDY pin pulses low to indicate the completion of this
EEMEM storage. There are also 13 addresses with two bytes
each of user-defined data that can be stored in the EEMEM
register from Address 2 to Address 14.
The following instructions facilitate the programming needs
of the user (see Table 7 for details):
0. Do nothing.
1. Restore EEMEM content to RDAC.
2. Store RDAC setting to EEMEM.
3. Store RDAC setting or user data to EEMEM.
4. Decrement by 6 dB.
5. Decrement all by 6 dB.
6. Decrement by one step.
7. Decrement all by one step.
8. Reset EEMEM content to RDAC.
9. Read EEMEM content from SDO.
10. Read RDAC wiper setting from SDO.
11. Write data to RDAC.
12. Increment by 6 dB.
13. Increment all by 6 dB.
14. Increment by one step.
15. Increment all by one step.
Table 14 to Table 20 provide programming examples that use
some of these commands.
SCRATCHPAD AND EEMEM PROGRAMMING
The scratchpad RDAC register directly controls the position of
the digital potentiometer wiper. For example, when the scratchpad
register is loaded with all 0s, the wiper is connected to Terminal B
of the variable resistor. The scratchpad register is a standard
logic register with no restriction on the number of changes
allowed, but the EEMEM registers have a program erase/write
cycle limitation.
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the scratchpad register) is accomplished by
loading the serial data input register with Instruction 11 (0xB),
Address 0, and the desired wiper position data. When the proper
wiper position is determined, the user can load the serial data
input register with Instruction 2 (0x2), which stores the wiper
position data in the EEMEM register. After 15 ms, the wiper
position is permanently stored in nonvolatile memory.
Table 5 provides a programming example listing the sequence
of the serial data input (SDI) words with the serial data output
appearing at the SDO pin in hexadecimal format.
Table 5. Write and Store RDAC Settings to EEMEM Registers
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes data 0x100 to the RDAC1 register,
Wiper W1 moves to 1/4 full-scale position.
0x20XXXX
0xB00100
Stores RDAC1 register content into the
EEMEM1 register.
0xB10200
0x20XXXX
Writes Data 0x200 to the RDAC2 register,
Wiper W2 moves to 1/2 full-scale position.
0x21XXXX
0xB10200
Stores RDAC2 register contents into the
EEMEM2 register.
At system power-on, the scratchpad register is automatically
refreshed with the value previously stored in the corresponding
EEMEM register. The factory-preset EEMEM value is midscale.
The scratchpad register can also be refreshed with the contents
of the EEMEM register in three different ways. First, executing
Instruction 1 (0x1) restores the corresponding EEMEM value.
Second, executing Instruction 8 (0x8) resets the EEMEM values
of both channels. Finally, pulsing the PR pin refreshes both
EEMEM settings. Operating the hardware control PR function
requires a complete pulse signal. When PR goes low, the internal
logic sets the wiper at midscale. The EEMEM value is not
loaded until PR returns high.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5242BRU1M-REEL7 | IC DGTL POT 256POS 16-TSSOP T/R |
| AD5243BRM50-RL7 | IC DGTL POT DUAL 50K I2C 10-MSOP |
| AD5245BRJ50-R2 | IC POT DGTL 50K 256POS SOT23-8 |
| AD5246BKS50-R2 | IC POT DGTL 50K 128POS SC70-6 |
| AD5247BKSZ100-1RL7 | IC POT DGTL 100K 128POS SC70-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5235BRU-REEL7 | 制造商:Analog Devices 功能描述:- Tape and Reel |
| AD5235BRUZ25 | 功能描述:IC DGTL POT DUAL 1024POS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5235BRUZ25 | 制造商:Analog Devices 功能描述:Digital Potentiometer IC Package/Case:16 |
| AD5235BRUZ250 | 功能描述:IC DGTL POT DUAL 1024POS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5235BRUZ250-R7 | 功能描述:IC DGTL POT DUAL 1024POS 16TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。