As the current increases through the voice coil, VC incre" />
參數資料
型號: AD5398BCPZ-REEL7
廠商: Analog Devices Inc
文件頁數: 6/17頁
文件大?。?/td> 0K
描述: IC DAC 10BIT CURRENT-SINK 8LFCSP
產品培訓模塊: Data Converter Fundamentals
DAC Architectures
標準包裝: 1
設置時間: 250µs
位數: 10
數據接口: I²C,串行
轉換器數目: 1
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-VFDFN 裸露焊盤,CSP
供應商設備封裝: 8-LFCSP-VD(3x3)
包裝: 標準包裝
輸出數目和類型: 1 電流,單極
采樣率(每秒): 31k
產品目錄頁面: 782 (CN2011-ZH PDF)
其它名稱: AD5398BCPZ-REEL7DKR
AD5398
Rev. B | Page 13 of 16
As the current increases through the voice coil, VC increases
and VDROP decreases and eventually approaches the minimum
specified compliance voltage of 600 mV. The ground return
path is modelled by the components RG and LG. The track
resistance between the voice coil and the AD5398 is modelled as
RT. The inductive effects of LG influence RSENSE and RC equally,
and because the current is maintained as a constant, it is not as
critical as the purely resistive component of the ground return
path. When the maximum sink current is flowing through the
motor, the resistive elements, RT and RG, might have an impact
on the voltage headroom of Q1 and could, in turn, limit the
maximum value of RC because of voltage compliance.
For example:
VBAT = 3.6 V
RG = 0.5 Ω
RT = 0.5 Ω
ISINK = 120 mA
VDROP = 600 mV (the compliance voltage)
Then the largest value of resistance of the voice coil, RC, is
=
×
+
×
+
=
SINK
G
SINK
T
SINK
DROP
BAT
C
I
R
I
R
I
V
R
)]
(
)
(
[
Ω
24
mA
120
Ω)]
0.5
mA
(120
2
mV
[600
V
3.6
=
×
+
For this reason it is important to minimize any series impedance
on both the ground return path and interconnect between the
AD5398 and the motor.
The power supply of the AD5398 should be decoupled with
0.1 μF and 10 μF capacitors. These capacitors should be kept as
physically close as possible, with the 0.1 μF capacitor serving as
a local bypass capacitor, and therefore should be located as close
as possible to the VDD pin. The 10 μF capacitor should be a
tantalum bead-type; the 0.1 μF capacitor should be a ceramic
type with a low effective series resistance and effective series
inductance. The 0.1 μF capacitor provides a low impedance path
to ground for high transient currents.
The power supply line should have as large a trace as possible to
provide a low impedance path and reduce glitch effects on the
supply line. Clocks and other fast switching digital signals
should be shielded from other parts of the board by digital
ground. Avoid crossover of digital and analog signals if possible.
When traces cross on opposite sides of the board, ensure that
they run at right angles to each other to reduce feedthrough
effects through the board. The best board layout technique is to
use a multilayer board with ground and power planes, where
the component side of the board is dedicated to the ground
plane only and the signal traces are placed on the solder side.
However, this is not always possible with a 2-layer board.
The exposed paddle on the AD5398 should be soldered to
ground to ensure the best possible thermal performance. The
thermal impedance of the AD5398 LFCSP package is 48°C/W
when soldered in a 4-layer board. It is defined in the Absolute
相關PDF資料
PDF描述
VI-JVN-MZ-F3 CONVERTER MOD DC/DC 18.5V 25W
VI-JVN-MZ-F1 CONVERTER MOD DC/DC 18.5V 25W
MS27472E24A2SB CONN RCPT 100POS WALL MT W/SCKT
VI-J53-MZ-F2 CONVERTER MOD DC/DC 24V 25W
MS27468T25F19SB CONN RCPT 19POS JAM NUT W/SCKT
相關代理商/技術參數
參數描述
AD5398BCPZ-WP 制造商:Analog Devices 功能描述:DAC 1-CH 10-bit 8-Pin LFCSP EP 制造商:Analog Devices 功能描述:10BIT DAC SINGLE SMD 5398 LFCSP8
AD5398BCSURF 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD5398BCSURFZ 功能描述:IC DAC 10BIT CURR-SINK 9WLCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散(最大):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率(每秒):*
AD5399YRM 制造商:Analog Devices 功能描述:DAC 2-CH 12-bit 10-Pin MSOP 制造商:Analog Devices 功能描述:12BIT DAC INT REF DUAL SMD 5399
AD5399YRM-REEL7 制造商:Analog Devices 功能描述:DAC 2-CH 12-bit 10-Pin MSOP T/R