- 您現在的位置：買賣IC網 > PDF目錄1890 > AD5535ABCZ (Analog Devices Inc)IC DAC 14BIT 32CHAN 124CSPBGA PDF資料下載
參數資料
| 型號： | AD5535ABCZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT 32CHAN 124CSPBGA |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 設置時間： | 65µs |
| 位數： | 14 |
| 數據接口： | 串行 |
| 轉換器數目： | 32 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 594mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 124-LBGA，CSPBGA |
| 供應商設備封裝： | 124-CSPBGA（15x15） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 32 電壓，單極 |
| 采樣率（每秒）： | 1.2M |
| 配用： | EVAL-AD5535EBZ-ND - BOARD EVALUATION FOR AD5535 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
AD5535
Rev. A | Page 15 of 16
Use as large a trace as possible for the supply lines of the device
to provide low impedance paths and reduce the effects of glitches
on the power supply line. Components, such as clocks with fast-
switching signals, should be shielded with digital ground to avoid
radiating noise to other sections of the board. Clock signals
should never be run near the analog inputs of the device. Avoid
crossovers of digital and analog signals. Traces for analog inputs
should be kept as wide and short as possible and should be
shielded with analog ground if possible. Traces on opposite
sides of a 2-layer printed circuit board should run at right
angles to each other to reduce the effects of feedthrough
through the board.
POWER SUPPLY SEQUENCING AND DECOUPLING
RECOMMENDATIONS
The diagram in Figure 23 shows the recommended decoupling
and power supply protection for the AD5535. On the AD5535,
it is recommended to tie all grounds together as close to the device
as possible. If the number of supplies must be reduced, all supplies
should be brought back separately and a provision should be
made on the board via a link option to drive the AVCC and V+
from the same supply. All power supplies should be adequately
decoupled with 10 μF tantalum and 0.1 μF ceramic capacitors.
Note that the capacitors on the VPP supply must be rated at
greater than 210 V. To overcome issues associated with power
supply sequencing when using high voltage supplies, the use of
protection diodes as indicated in
A microstrip technique is by far the best, but it is not always
possible to use with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes,
and signals are placed on the solder side. Multilayer printed
circuit boards with dedicated ground, power, and tracking
layers offer the optimum solution in terms of obtaining analog
performance, but at increased manufacturing costs.
Figure 23 is recommended.
AGND
DACGND
DGND
DVCC
AVCC
VPP
PGND
V–
V+
AVCC = +5V
DVCC = +5V
VPP = +210V
V+ = +5V
V– = –5V
AD5535
SD103C
RS1G
10
μF
10
μF
0.1
μF
0.1
μF
0.1
μF
10
μF
10
μF
10
μF
0.1
μF
0.1
μF
HIGH VOLTAGE DIODE
MANUFACTURER: GS
SCHOTTKY DIODE
MANUFACTURER: ITT
05068-017
Good decoupling is vitally important when using high resolu-
tion converters. All analog supplies should be decoupled with
10 μF tantalum in parallel with 0.1 μF ceramic capacitors to
analog ground. To achieve the best from the decoupling
components, these should be placed as close to the device as
possible, ideally right up against the IC or the IC socket. The
main aim of a bypassing element is to maximize the charge
stored in the bypass loop while simultaneously minimizing the
inductance of this loop. Inductance in the loop acts as an
impedance to high frequency transients and results in power
supply spiking. By keeping the decoupling as close to the device
as possible, the loop area is kept as small as possible, thereby
reducing the possibility of power supply spikes. Digital supplies
of high resolution converters should be decoupled with 10 μF
tantalum and 0.1 μF ceramic to the digital ground plane. The
amplifiers’ V
Figure 23. Recommended Power Supply Sequencing and Decoupling
GUIDELINES FOR PRINTED
CIRCUIT BOARD LAYOUT
Printed circuit boards should be designed such that the analog
and digital sections are separated and confined to designated
analog and digital sections of the board. This facilitates the use
of ground planes that can be separated easily. A minimum etch
technique is generally found to be the best for ground planes
because it optimizes shielding of sensitive signal lines. Digital
and analog ground planes should be joined only in one place, at
the AGND and DGND pins of the high resolution converter.
Data and address buses on the board should be buffered or
latched to isolate the high frequency bus of the processor from
the bus of the high resolution converters. These act as a faraday
shield and increase the signal-to-noise performance of the
converters by reducing the amount of high frequency digital
coupling. Avoid running digital lines under the device because
they couple noise onto the die. The ground plane should be
allowed to run under the IC to avoid noise coupling.
and V
DD
SS
supplies should be decoupled with 10 μF
and 0.1 μF to AGND.
All logic chips should be decoupled with 0.1 μF to digital
ground to decouple high frequency effects associated with
digital circuitry.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5547BRU | IC DAC 16BIT DUAL 38-TSSOP |
| AD5560JSVUZ-REEL | IC DPS PROGRAMABLE W/DAC 64TQFP |
| AD557JN | IC DAC 8BIT V-OUT 16-DIP |
| AD561KD | IC DAC 10BIT 5-15V IN MONO 16DIP |
| AD565AKD | IC DAC 12BIT MONO 250NS 24-CDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5535B | 制造商:AD 制造商全稱:Analog Devices 功能描述:32-Channel, 14-Bit DAC with Full-Scale Output Voltage Programmable from 50 V to 200 V |
| AD5535BKBC | 制造商:Analog Devices 功能描述:BUILT-IN CAPACITANCE CERAMIC RESONATOR 制造商:Analog Devices 功能描述:32-CHANNEL DAC WITH 200V AMPLIFIER - Trays 制造商:Analog Devices 功能描述:IC DAC 14BIT SRL 124CSPBGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC IC 32-CH w/ 200V AMP |
| AD5535BKBCZ | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| ad5535bru | 制造商:Analog Devices 功能描述: |
| AD5539 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultrahigh Frequency Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。