- 您現在的位置：買賣IC網 > PDF目錄1890 > AD5560JSVUZ-REEL (Analog Devices Inc)IC DPS PROGRAMABLE W/DAC 64TQFP PDF資料下載
參數資料
| 型號： | AD5560JSVUZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 37/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DPS PROGRAMABLE W/DAC 64TQFP |
| 設計資源： | Integrated Device Power Supply for PAD with Output Voltage Range 0 V to 25 V (CN0130) |
| 標準包裝： | 1,500 |
| 類型： | 電源 |
| 應用： | 自動測試設備 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-TQFP 裸露焊盤 |
| 供應商設備封裝： | 64-TQFP-EP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
AD5560
Data Sheet
Rev. D | Page 42 of 68
PACKAGE COMPOSITION AND MAXIMUM
VERTICAL FORCE
The exposed pad and leads of the TQFP package have a 100%
tin finish. The exposed paddle is connected internally to AVSS.
The simulated maximum allowable force for a single lead is
0.18 lbs; total allowable force for the package is 11.5 lbs. The
quoted maximum force may cause permanent lead bending.
Other package failure (die, mold, board) may occur first at
lower forces.
SLEW RATE CONTROL
There are two methods of achieving different slew rates using
the AD5560. One method is using the programmable slew rate
feature that gives eight programmable rates. The second
method is using the ramp feature and an external clock.
Programmable Slew Rate
Eight programmable modes of slew rates are available to choose
from through the serial interface, enabling the user to choose
different rates to power up the DUT. The different slew rates
are achieved by variation in the internal compensation of the
force DAC output amplifier. The slew rates available are
1.000 V/s, 0.875 V/s, 0.750 V/s, 0.625 V/s, 0.5 V/s,
0.4375 V/s, 0.35V s, and 0.313 V/s.
Ramp Function
Included in the AD5560 is a ramp function that enables the
user to apply a rising or falling voltage ramp to the DUT. The
user supplies a clock, RCLK, to control the timing.
This function is controlled via the serial interface and requires
programming of a number of registers to determine the end
value, the ramp size, and the clock divider register to determine
the update rate.
The contents of the FIN DAC x1 register are the ramp start
value. The user must load the end code register and the step
size register. The sign is now generated from the difference
between the FIN DAC x1 register and the end code; then the
step size value is added to or subtracted from FIN DAC x1,
calibrated and stored. The user must supply a clock to the RCLK
pin to load the new code to the DAC. The output settles in 1.2 s
for a step of 10 mV with CDUT in the lowest range of <0.2 F.
While the output is settling, the next step is calculated to be
ready for the next ramp clock. The calibration engine is used
here; therefore, there is a calibration delay of 1.2 s.
The ramp timing is controlled in two ways: by a user-supplied
clock (RCLK) and by a clock divider register. This gives the
user much flexibility over the frequency of the ramp steps. The
ramp typically starts after (2 × clock divider + 2) clocks,
although there can be a ±1 clock delay due to the asynchronous
nature of RCLK. The external clock can be a maximum of 833
kHz when using clock divider = 1. Faster RCLK speeds can be
used, but the fastest ramp rate is linked into the DAC
calibration engine.
For slower ramp rates, an even slower RCLK can be used.
The step sizes are in multiples of 16 LSBs. If the code previous
to the end code is not a multiple of this step size, the last step is
smaller. If the ramp function must be interrupted at any stage
during the ramp, write the interrupt ramp command. The FIN
DAC x1 stops ramping at the current value and returns to
normal operation.
The fastest ramp rate is 0.775 V/s (for a 5 V reference and an
833 kHz clock using a 2032 LSB step size and divider = 1).
The slowest ramp rate is 24 V/s (for a 5 V reference and an
833 kHz clock using a 16 LSB step size and divider = 255).
Even slower ramps can be achieved with slower SCLK. The
ramp continues until any of the following occurs:
It reaches the end code.
An interrupt ramp is received from the user.
If any enabled alarm triggers, the ramp stops to allow
the user to service the activated alarm.
While the device is in ramp mode, the only command that the
interface accepts is an interrupt ramp. No other commands should
be written to the device while ramping because they are ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| AD557JN | IC DAC 8BIT V-OUT 16-DIP |
| AD561KD | IC DAC 10BIT 5-15V IN MONO 16DIP |
| AD565AKD | IC DAC 12BIT MONO 250NS 24-CDIP |
| AD5663BCPZ-R2 | IC DAC NANO 16BIT DUAL 10-LFCSP |
| AD5678BRUZ-1 | IC DAC 12/16BIT SPI/SRL 14TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5561JBCZ | 制造商:Analog Devices 功能描述: |
| AD5562ACPZ-R7 | 制造商:Analog Devices 功能描述: |
| AD5564B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| AD557 | 制造商:AD 制造商全稱:Analog Devices 功能描述:a DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD557_01 | 制造商:AD 制造商全稱:Analog Devices 功能描述:a DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
發布緊急采購，3分鐘左右您將得到回復。