- 您現在的位置：買賣IC網 > PDF目錄8593 > AD5669RBRUZ-2-RL7 (Analog Devices Inc)IC DAC 16BIT I2C/SRL 16TSSOP PDF資料下載
參數資料
| 型號： | AD5669RBRUZ-2-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/32頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT I2C/SRL 16TSSOP |
| 標準包裝： | 1,000 |
| 系列： | denseDAC |
| 設置時間： | 2.5µs |
| 位數： | 16 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 8 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | * |
| 采樣率（每秒）： | 166k |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD5629R/AD5669R
Rev. D | Page 25 of 32
POWER-DOWN MODES
The AD5629R/AD5669R contain four separate modes of
operation. Command 0100 is reserved for the power-down
function (see Table 8). These modes are software-programmable
by setting two bits, Bit DB9 and Bit DB8, in the control register.
Table 12 shows how the state of the bits corresponds to the
mode of operation of the device. Any or all DACs (DAC H to
DAC A) can be powered down to the selected mode by setting
the corresponding eight bits (DB7 to DB0) to 1. See Table 13 for
the contents of the input shift register during power-down/power-
up operation.
When both bits are set to 0, the part works normally with its
normal power consumption of 1.3 mA at 5 V. However, for the
three power-down modes, the supply current falls to 0.4 A at
5 V (0.2 A at 3 V). Not only does the supply current fall, but
the output stage is also internally switched from the output of
the amplifier to a resistor network of known values. This has the
advantage that the output impedance of the part is known while
the part is in power-down mode. There are three different
options. The output is connected internally to GND through
either a 1 k or a 100 k resistor, or it is left open-circuited
(three-state). The output stage is illustrated in Figure 55.
RESISTOR
NETWORK
VOUT
RESISTOR
STRING DAC
POWER-DOWN
CIRCUITRY
AMPLIFIER
08819-
051
Figure 55. Output Stage During Power-Down
The bias generator of the selected DAC(s), output amplifier,
resistor string, and other associated linear circuitry is shut down
when the power-down mode is activated. The internal reference
is powered down only when all channels are powered down.
However, the contents of the DAC register are unaffected when
in power-down. The time to exit power-down is typically 4 s
for VDD = 5 V and for VDD = 3 V.
Any combination of DACs can be powered up by setting PD1
and PD0 to 0 (normal operation). The output powers up to the
value in the input register (LDAC low) or to the value in the
DAC register before powering down (LDAC high).
CLEAR CODE REGISTER
The AD5629R/AD5669R have a hardware CLR pin that
is an asynchronous clear input. The CLR input is falling edge
sensitive. Bringing the CLR line low clears the contents of the
input register and the DAC registers to the data contained in
the user-configurable CLR register and sets the analog outputs
accordingly. This function can be used in system calibration to load
zero scale, midscale, or full scale to all channels together. These
clear code values are user-programmable by setting two bits, Bit
DB1 and Bit DB0, in the CLR control register (see Table 15).
The default setting clears the outputs to 0 V. Command 0101
is reserved for loading the clear code register (see Table 8).
The part exits clear code mode at the end of the next valid write
to the part. If CLR is activated during a write sequence, the write
is aborted.
The CLR pulse activation time (the falling edge of CLR to when
the output starts to change) is typically 280 ns. However, if
outside the DAC linear region, it typically takes 520 ns after
executing CLR for the output to start changing (see Figure 44).
See Table 14 for the contents of the input shift register during
the loading clear code register operation.
Table 10. Internal Reference Register
Internal REF Register (DB0)
Action
0
Reference off (default)
1
Reference on
Table 11. 32-Bit Input Shift Register Contents for Reference Set-Up Command
MSB
LSB
DB23
DB22
DB21
DB20
DB19
DB18
DB17
DB16
DB15 to DB1
DB0
1
0
X
1/0
Command bits (C3 to C0)
Address bits (A3 to A0)—don’t cares
Don’t cares
Internal REF on/off
相關PDF資料 |
PDF描述 |
|---|---|
| AD5348BRU | IC DAC 12BIT OCTAL VOUT 38-TSSOP |
| VI-23D-MY-B1 | CONVERTER MOD DC/DC 85V 50W |
| VE-B6L-MV-B1 | CONVERTER MOD DC/DC 28V 150W |
| VI-23B-MY-B1 | CONVERTER MOD DC/DC 95V 50W |
| VE-B6H-MV-B1 | CONVERTER MOD DC/DC 52V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD566A | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed 12-Bit Monolithic D/A Converters |
| AD566AJCWG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter |
| AD566AJD | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed 12-Bit Monolithic D/A Converters |
| AD566AJN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:12-Bit Digital-to-Analog Converter |
發布緊急采購，3分鐘左右您將得到回復。