- 您現在的位置：買賣IC網 > PDF目錄10049 > AD573KNZ (Analog Devices Inc)IC ADC 10BIT SAR REGISTER 20DIP PDF資料下載
參數資料
| 型號： | AD573KNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT SAR REGISTER 20DIP |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 50k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 800mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
AD573
–5–
BIPOLAR CONNECTION
To obtain the bipolar –5 V to +5 V range with an offset binary
output code, the bipolar offset control pin is left open.
A –5.000 volt signal will give a 10-bit code of 00000000 00; an
input of 0.000 volts results in an output code of 10000000 00
and +4.99 volts at the input yields the 11111111 11 code. The
nominal transfer curve is shown in Figure 6.
Figure 6. AD573 Transfer Curve— Bipolar Operation
Note that in the bipolar mode, the code transitions are offset
1/2 LSB such that an input voltage of 0 volts
±5 mV yields the
code representing zero (10000000 00). Each output code is then
centered on its nominal input voltage.
Full-Scale Calibration
Full-Scale Calibration is accomplished in the same manner as in
unipolar operation except the full scale input voltage is +4.985
volts.
Negative Full-Scale Calibration
The circuit in Figure 4a can also be used in bipolar operation to
offset the input voltage (nominally –5 V) which results in the
00000000 00 code. R2 should be omitted to obtain a symmetri-
cal range.
The bipolar offset control input is not directly TTL compatible
but a TTL interface for logic control can be constructed as
shown in Figure 7.
Figure 7. Bipolar Offset Controlled by Logic Gate
Gate Output = 1 Unipolar 0–10 V Input Range
Gate Output = 0 Bipolar
±5 V Input Range
SAMPLE-HOLD AMPLIFIER CONNECTION TO THE
AD573
Many situations in high speed acquisition systems or digitizing
rapidly changing signals require a sample-hold amplifier (SHA)
in front of the A/D converter. The SHA can acquire and hold a
signal faster than the converter can perform a conversion. A
SHA can also be used to accurately define the exact point in
time at which the signal is sampled. For the AD573, a SHA can
also serve as a high input impedance buffer.
Figure 8 shows the AD573 connected to the AD582 monolithic
SHA for high speed signal acquisition. In this configuration, the
AD582 will acquire a 10 volt signal in less than 10
s with a
droop rate less than 100
V/ms.
Figure 8. Sample-Hold Interface to the AD573
DR
goes high after the conversion is initiated to indicate that
reset of the SAR is complete. In Figure 8 it is also used to put
the AD582 into the hold mode while the AD573 begins its con-
version cycle. (The AD582 settles to final value well in advance
of the first comparator decision inside the AD573).
DR
goes low when the conversion is complete placing the
AD582 back in the sample mode. Configured as shown in Fig-
ure 8, the next conversion can be initiated after a 10
s delay to
allow for signal acquisition by the AD582.
Observe carefully the ground, supply, and bypass capacitor con-
nections between the two devices. This will minimize ground
noise and interference during the conversion cycle.
GROUNDING CONSIDERATIONS
The AD573 provides separate Analog and Digital Common
connections. The circuit will operate properly with as much as
±200 mV of common-mode voltage between the two commons.
This permits more flexible control of system common bussing
and digital and analog returns.
In normal operation, the Analog Common terminal may gener-
ate transient currents of up to 2 mA during a conversion. In ad-
dition a static current of about 2 mA will flow into Analog
Common in the unipolar mode after a conversion is complete.
The Analog Common current will be modulated by the varia-
tions in input signal.
The absolute maximum voltage rating between the two com-
mons is
±1 volt. It is recommended that a parallel pair of
back-to-back protection diodes be connected between the com-
mons if they are not connected locally.
REV. B
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1349CSW#TR | IC TXRX RS232 5V SHTDN LP 28SOIC |
| VI-24M-IU-F4 | CONVERTER MOD DC/DC 10V 200W |
| VE-26F-MX-F2 | CONVERTER MOD DC/DC 72V 75W |
| MS27508E8A6S | CONN RCPT 6POS BOX MNT W/SCKT |
| VE-26T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD573KP | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit A/D Converter |
| AD573SD | 功能描述:模數轉換器 - ADC IC MONO 10-BIT RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD573SD/883B | 制造商:Analog Devices 功能描述:ADC SGL SAR 10-BIT PARALLEL 20PIN SBCDIP - Rail/Tube 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC IC MONO 10-BIT A/D CONV 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC IC MONO 10-BIT 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD574 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converter |
| AD574038F | 制造商:AD 功能描述:New |
發布緊急采購，3分鐘左右您將得到回復。