- 您現在的位置：買賣IC網 > PDF目錄10049 > AD573KNZ (Analog Devices Inc)IC ADC 10BIT SAR REGISTER 20DIP PDF資料下載
參數資料
| 型號： | AD573KNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/10頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SAR REGISTER 20DIP |
| 標準包裝： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 50k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 800mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 20-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
AD573
–6–
CONTROL AND TIMING OF THE AD573
The operation of the AD573 is controlled by three inputs:
CONVERT
, HBE and LBE.
Starting a Conversion
The conversion cycle is initiated by a positive going CONVERT
pulse at least 500 ns wide. The rising edge of this pulse resets
the internal logic, clears the result of the previous conversion,
and sets DR high. The falling edge of CONVERT begins the
conversion cycle. When conversion is completed DR returns
low. During the conversion cycle, HBE and LBE should be held
high. If HBE or LBE goes low during a conversion, the data
output buffers will be enabled and intermediate conversion re-
sults will be present on the data output pins. This may cause
bus conflicts if other devices in a system are trying to use the bus.
tCS
tDSC
VOH + VOL
2
VIH + VIL
2
tC
CONVERT
DR
Figure 9. Convert Timing
Reading the Data
The three-state data output buffers are enabled by HBE and
LBE
. Access time of these buffers is typically 150 ns (250 maxi-
mum). The data outputs remain valid until 50 ns after the en-
able signal returns high, and are completely into the high
impedance state 100 ns later.
VIH + VIL
2
LBE OR HBE
tHD
tDD
VOH
VOL
DATA
VALID
tHL
HIGH
IMPEDANCE
HIGH
IMPEDANCE
DB0–DB7
OR
DB8–DB9
Figure 10. Read Timing
TIMING SPECIFICATIONS (All grades, TA = TMIN–TMAX)
Parameter
Symbol Min Typ
Max Units
CONVERT Pulse Width
tCS
500 –
–
ns
DR
Delay from CONVERT tDSC
–
1
1.5
s
Conversion Time
tC
10
20
30
s
Data Access Time
tDD
0
150
250
ns
Data Valid after HBE/LBE
High
tHD
50
–
ns
Output Float Delay
tHL
–
100
200
ns
MICROPROCESSOR INTERFACE CONSIDERATIONS—
GENERAL
When an analog-to-digital converter like the AD573 is inter-
faced to a microprocessor, several details of the interface must
be considered. First, a signal to start the converter must be gen-
erated; then an appropriate delay period must be allowed to pass
before valid conversion data may be read. In most applications,
the AD573 can interface to a microprocessor system with little
or no external logic.
The most popular control signal configuration consists of de-
coding the address assigned to the AD573, then gating this sig-
nal with the system’s WR signal to generate the CONVERT
pulse, and gating it with RD to enable the output buffers. The
use of a memory address and memory WR and RD signals de-
notes “memory-mapped” I/O interfacing, while the use of a
separate I/O address space denotes “isolated I/O” interfacing. In
8-bit bus systems, the 10-bit AD573 will occupy two locations
when data is to be read; therefore, two (usually consecutive) ad-
dresses must be decoded. One of the addresses can also be used
as the address which produces the CONVERT signal during
WR operations.
Figure 11 shows a generalized diagram of the control logic for
an AD573 interfaced to an 8-bit data bus, where two addresses
(ADC ADDR and ADC ADDR + 1) have been decoded. ADC
ADDR starts the converter when written to (the actual data be-
ing written to the converter does not matter) and contains the
high byte data during read operations. ADC ADDR + 1 per-
forms no function during write operations, but contains the low
byte data during read operations.
Figure 11. General AD573 Interface to 8-Bit Microprocessor
In systems where this read-write interface is used, at least 30
microseconds (the maximum conversion time) must be allowed
to pass between starting a conversion and reading the results.
This delay or “timeout” period can be implemented in a short
software routine such as a countdown loop, enough dummy in-
structions to consume 30 microseconds, or enough actual useful
instructions to consume the required time. In tightly-timed sys-
tems, the DR line may be read through an external three-state
buffer to determine precisely when a conversion is complete.
Higher speed systems may choose to use DR to signal an inter-
rupt to the processor at the end of a conversion.
Figure 12. Typical AD573 Interface Timing Diagram
REV. B
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1349CSW#TR | IC TXRX RS232 5V SHTDN LP 28SOIC |
| VI-24M-IU-F4 | CONVERTER MOD DC/DC 10V 200W |
| VE-26F-MX-F2 | CONVERTER MOD DC/DC 72V 75W |
| MS27508E8A6S | CONN RCPT 6POS BOX MNT W/SCKT |
| VE-26T-MX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD573KP | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit A/D Converter |
| AD573SD | 功能描述:模數轉換器 - ADC IC MONO 10-BIT RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD573SD/883B | 制造商:Analog Devices 功能描述:ADC SGL SAR 10-BIT PARALLEL 20PIN SBCDIP - Rail/Tube 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC IC MONO 10-BIT A/D CONV 制造商:Analog Devices Inc. 功能描述:Analog to Digital Converters - ADC IC MONO 10-BIT 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD574 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 12-Bit A/D Converter |
| AD574038F | 制造商:AD 功能描述:New |
發布緊急采購，3分鐘左右您將得到回復。