- 您現在的位置：買賣IC網 > PDF目錄3887 > PIC16CE623T-30/SO (Microchip Technology)IC MCU OTP 512X14 EE COMP 18SOIC PDF資料下載
參數資料
| 型號： | PIC16CE623T-30/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 8/100頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU OTP 512X14 EE COMP 18SOIC |
| 標準包裝： | 1,100 |
| 系列： | PIC® 16C |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 30MHz |
| 外圍設備： | 欠壓檢測/復位，POR，WDT |
| 輸入/輸出數： | 13 |
| 程序存儲器容量： | 896B（512 x 14） |
| 程序存儲器類型： | OTP |
| EEPROM 大?。?/td> | 128 x 8 |
| RAM 容量： | 96 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 18-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | PIC16CE623T30/SO |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
2010 Microchip Technology Inc.
DS39935C-page 105
ENC424J600/624J600
11.0 FLOW CONTROL
Flow control provides a mechanism for network
stations to temporarily stop transmission of data to
themselves. This feature is commonly used to prevent
buffer overruns while receiving data.
ENC424J600/624J600 devices are capable of both
automatic and manual flow control. The hardware can
advertise when it is temporarily unable to receive data
and delay transmissions when a remote system does
the same. Flow control is supported for both full and
half-duplex links. It can either be initiated manually by
software, or configured to enable automatically when
insufficient space remains in the receive buffer
memory.
Flow control operation is configured by the FCOP<1:0>
bits (ECON1<7:6>), the AUTOFC bit (ECON2<7>), the
RXPAUS and PASSALL bits (MACON1<2:1>), and the
EPAUS and ERXWM registers in some modes.
11.1
Modes of Operation
Flow control operation differs between full and
half-duplex links. Both modes are supported, but it is
important to understand the difference before enabling
flow control in an application.
11.1.1
HALF-DUPLEX MODE
When the link is operating in Half-Duplex mode, flow
control operates by jamming the network. The node
wishing to inhibit transmissions to itself sends a
preamble pattern of alternating ones and zeros (55h)
on the medium; this is also known as asserting back
pressure on the link. Since the link is operating under
Half-Duplex mode, all connected nodes must wait
before transmitting. If a node does transmit, compliant
nodes will detect the collision and wait until the
jamming stops to retransmit. This effectively jams the
network until flow control is disabled.
If a frame is to be transmitted while flow control is
enabled, the ENCX24J600 will stop jamming, wait the
standard Inter-Packet Gap (IPG) delay, then attempt to
transmit. Because all traffic was previously jammed,
several nodes may begin transmitting and several
collisions may occur. The hardware will transmit and
resume jamming as soon as possible, but it is feasible
for other nodes to transmit packets before this
happens. This limitation of flow control in half-duplex
operation cannot be avoided.
Given the detrimental effect that back pressure based
flow control inflicts on a network, along with the
possible lack of effectiveness, it is recommended that
flow control be avoided in Half-Duplex mode unless the
application is used in a closed network environment
with proper testing.
When operating in Half-Duplex mode, setting
FCOP<1:0> to ‘00’ disables the flow control. Any other
combination enables flow control and causes the
device to jam the network.
11.1.2
FULL-DUPLEX MODE
Flow control for full-duplex links is much more robust.
Instead of jamming the network, a station can send a
pause control frame to the remote system. The pause
frame is directed to a special Multicast destination
address (01-08-C2-00-00-01) and indicates how long
the remote node should wait before transmitting again.
This time is expressed in units of pause quanta, where
one pause quanta is equal to 512 bit times.
While a station is silenced or paused, reception is still
enabled. If another pause control frame arrives, any
previous value is discarded and the timer restarts using
the new pause time value. If the received control frame
has a timer value of zero, the pause is terminated and
transmission resumes immediately.
When operating in Full-Duplex mode, each combina-
tion of FCOP<1:0> has a different effect on transmitting
control frames. These combinations are discussed in
11.1.3
TRANSMITTING AND RECEIVING
PAUSE CONTROL FRAMES
The ENCX24J600 automatically processes incoming
pause control frames without application intervention.
When a pause control frame is received, the MAC
internally sets the pause timer. Transmission is inhib-
ited while the timer is active. If an application attempts
to transmit a packet during this time, the transmission
logic will stall until the time expires (i.e., TXRTS will
stay set for longer than normal).
Pause control frames are normally filtered out by the
MAC and are not written to the receive buffer. Setting the
PASSALL bit (MACON1<1>) alters this behavior and
causes these frames to pass through the receive filters.
If the frame is accepted, it will be written to the receive
buffer. However, setting PASSALL will also cause the
MAC to not process the pause control frame. The trans-
mission logic will allow immediate transmission without
regard to the remote pause requests.
Before using either automatic or manual flow control,
set the pause time value with the EPAUS register. This
value controls the pause time value that is transmitted
with each pause control frame. Each unit of pause
quanta in this register is equal to 512 bit times.
Note:
Flow control is an optional portion of the
IEEE 802.3 specification and may not be
implemented on all remote devices.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16F1825-E/ML | MCU PIC 14K FLASH 1K RAM 16QFN |
| PIC16F1828-I/SO | IC PIC MCU 8BIT 14KB FLSH 20SOIC |
| PIC16F688-I/SL | IC PIC MCU FLASH 4KX14 14SOIC |
| 22-02-3213 | CONN FFC/FPC VERTICAL 21POS .100 |
| 22-15-3193 | CONN FFC/FPC 19POS .100 RT ANG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD629B | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Common-Mode Voltage Difference Amplifier |
| AD629BN | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 制造商:Analog Devices 功能描述:AMP DIFF HI COM MODE VOLT DIP 629 |
| AD629BNZ | 功能描述:IC AMP DIFF 25MA LDRIFT 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD629BR | 功能描述:IC AMP DIFF 25MA LDRIFT 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| AD629BR-REEL | 功能描述:IC AMP DIFF 25MA LDRIFT 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。