- 您現在的位置：買賣IC網 > PDF目錄10279 > AD7495BRZ-REEL7 (Analog Devices Inc)IC ADC 12BIT SRL LP W/REF 8-SOIC PDF資料下載
參數資料
| 型號： | AD7495BRZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT SRL LP W/REF 8-SOIC |
| 標準包裝： | 1,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 10.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極 |
AD7475/AD7495
Rev. B | Page 16 of 24
OPERATING MODES
The AD7475/AD7495 operating mode is selected by controlling
the logic state of the CS signal during a conversion. There are
three possible modes of operation: normal mode, partial power-
down mode, and full power-down mode. The point at which CS
is pulled high after the conversion has been initiated determines
which power-down mode, if any, the device enters. Similarly, if
already in a power-down mode, CS can control whether the
device returns to normal operation or remains in power-down.
These modes of operation are designed to provide flexible
power management options. These options can be chosen to
optimize the power dissipation/throughput rate ratio for
differing application requirements.
NORMAL MODE
This mode is intended for fastest throughput rate performance,
because the user does not have to worry about any power-up
times with the AD7475/AD7495 remaining fully powered all
the time. Figure 19 shows the general diagram of the AD7475/
AD7495 operating in this mode.
The conversion is initiated on the falling edge of CS, as
described in the Serial Interface section. To ensure the part
remains fully powered-up at all times, CS must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
of CS. If CS is brought high any time after the 10
th SCLK falling
edge, but before the 16th SCLK falling edge, the part remains
powered up but the conversion is terminated and SDATA goes
back into three-state. Sixteen serial clock cycles are required to
complete the conversion and access the conversion result. CS
may idle high until the next conversion or may idle low until
sometime prior to the next conversion (effectively idling CS
low).
Once a data transfer is complete (SDATA has returned to three-
state), another conversion can be initiated after the quiet time,
tQUIET, has elapsed, by bringing CS low again.
PARTIAL POWER-DOWN MODE
This mode is intended for use in applications where slower
throughput rates are required; either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and then the ADC is
powered down for a relatively long duration between these
bursts of several conversions. When the AD7475 is in partial
power-down, all analog circuitry is powered down except for
the bias current generator; and, in the case of the AD7495, all
analog circuitry is powered down except for the on-chip
reference and reference buffer.
To enter partial power-down, the conversion process must be
interrupted by bringing CS high anywhere after the second
falling edge of SCLK and before the tenth falling edge of SCLK,
as shown in Figure 20. Once CS has been brought high in this
window of SCLKs, the part enters partial power-down, the
conversion that was initiated by the falling edge of CS is
terminated, and SDATA goes back into three-state. If CS is
brought high before the second SCLK falling edge, the part
remains in normal mode and does not power down. This avoids
accidental power-down due to glitches on the CS line.
SCLK
FOUR LEADING ZEROS + CONVERSION RESULT
SDATA
1
16
10
CS
01684-B
-019
Figure 19. Normal Mode
SCLK
1
16
10
2
CS
01684-B
-020
Figure 20. Entering Partial Power-Down Mode
相關PDF資料 |
PDF描述 |
|---|---|
| SL404MX | CONN PLUG 4POS MALE W/COUPLING |
| VI-B6H-IX-B1 | CONVERTER MOD DC/DC 52V 75W |
| AD7495BRZ-REEL | IC ADC 12BIT SRL LP W/REF 8-SOIC |
| MS27473E10B99SB | CONN PLUG 7POS STRAIGHT W/SCKT |
| LTC2355IMSE-12#TRPBF | IC ADC 12BIT 3.5MSPS 10-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7495BRZ-REEL73 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1MSPS,12-Bit ADCs |
| AD7495CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board for 1MSPS, 12-Bit ADC |
| AD75004 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad 12-Bit D/A Converter |
| AD75004KN | 制造商:Analog Devices 功能描述:DAC 4-CH Current Steering 12-bit 24-Pin PDIP Tube |
| AD75004KNZ | 功能描述:IC DAC 12BIT QUAD W/BUFF 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
發布緊急采購，3分鐘左右您將得到回復。