- 您現在的位置：買賣IC網 > PDF目錄10193 > AD7656YSTZ-1-RL (Analog Devices Inc)IC ADC 16BIT 6CH 250KSPS 64LQFP PDF資料下載
參數資料
| 型號： | AD7656YSTZ-1-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/32頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 6CH 250KSPS 64LQFP |
| 標準包裝： | 1,500 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 6 |
| 功率耗散（最大）： | 143mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 6 個單端，雙極 |
| 配用： | EVAL-AD7656-1EDZ-ND - BOARD EVAL CONTROL AD7656-1 EVAL-AD7656-1CBZ-ND - BOARD EVAL FOR AD7656-1 EVAL-AD7656CBZ-ND - BOARD EVAL FOR AD7656 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7656-1/AD7657-1/AD7658-1
Rev. D | Page 25 of 32
CHANGING THE ANALOG INPUT RANGE
(H/S SEL = 0)
The AD7656-1/AD7657-1/AD7658-1 RANGE pin allows the
user to select either ±2 × VREF or ±4 × VREF as the analog input
range for the six analog inputs. When the H/S SEL pin is low,
the logic state of the RANGE pin is sampled on the falling edge of
the BUSY signal to determine the range for the next simultaneous
conversion. When the RANGE pin is logic high at the falling
edge of the BUSY signal, the range for the next conversion is
±2 × VREF. When the RANGE pin is logic low at the falling
edge of the BUSY signal, the range for the next conversion is
±4 × VREF. After a RESET pulse, the range is updated on the first
falling BUSY edge.
CHANGING THE ANALOG INPUT RANGE
(H/S SEL = 1)
When the H/S SEL pin is high, the range can be changed by
writing to the control register. DB[12:10] in the control register
are used to select the analog input ranges for the next conversion.
Each analog input pair has an associated range bit, allowing
independent ranges to be programmed on each ADC pair. When
the RNGx bit is set to 1, the range for the next conversion is ±2
× VREF. When the RNGx bit is set to 0, the range for the next
conversion is ±4 × VREF.
Serial Interface (SER/PAR SEL = 1)
By pulsing one, two, or all three CONVST signals, the AD7656-1/
AD7657-1/AD7658-1 use their on-chip trimmed oscillator to
simultaneously convert the selected channel pairs on the rising
edge of CONVST. After the rising edge of CONVST, the BUSY
signal goes high to indicate that the conversion has started. It
returns low when the conversion is complete, 3 s later. Any
further CONVST rising edges on either CONVST A, CONVST B,
or CONVST C are ignored as long as BUSY is high. The output
register is loaded with the new conversion results, and data can
be read from the AD7656-1/AD7657-1/AD7658-1. To read the
data back from the parts over the serial interface, SER/PAR SEL
should be tied high. The CS and SCLK signals are used to transfer
data from the AD7656-1/AD7657-1/AD7658-1. The parts have
three DOUT pins: DOUT A, DOUT B, and DOUT C. Data
can be read back from each part using one, two, or all three
DOUT lines.
Figure 32 shows six simultaneous conversions and the read
sequence using three DOUT lines. Also in Figure 32, 32 SCLK
transfers are used to access data from the AD7656-1/AD7657-1/
AD7658-1; however, two 16-SCLK individually framed transfers
with the CS signal can also be used to access the data on the
three DOUT lines. Any additional SCLKs applied after this
result in an output of all zeros. When the serial interface is
selected and conversion data is clocking out on all three DOUT
lines, tie DB0/SEL A, DB1/SEL B, and DB2/SEL C to VDRIVE.
These pins are used to enable the DOUT A to DOUT C lines,
respectively.
If it is required to clock conversion data out on two data output
lines, use DOUT A and DOUT B. To enable DOUT A and
DOUT B, tie DB0/SEL A and DB1/SEL B to VDRIVE, and
DB2/SEL C should be tied low. When six simultaneous conversions
are performed and only two DOUT lines are used, a 48-SCLK
transfer can be used to access the data from the AD7656-1/
AD7657-1/AD7658-1. Any additional SCLKs applied after this
result in an output of all zeros. The read sequence is shown in
Figure 33 for a simultaneous conversion on all six ADCs using
two DOUT lines. If a simultaneous conversion occurred on all
six ADCs, and only two DOUT lines are used to read the results
from the AD7656-1/AD7657-1/AD7658-1, DOUT A clocks out
the result from V1, V2, and V5, whereas DOUT B clocks out
the results from V3, V4, and V6.
Data can also be clocked out using just one DOUT line, in which
case useDOUT A to access the conversion data. To configure
the AD7656-1/AD7657-1/AD7658-1 to operate in this mode,
tie DB0/SEL A to VDRIVE, and tie DB1/SEL B and DB2/SEL C
low. The disadvantage of using only one DOUT line is that the
throughput rate is reduced. Data can be accessed from the
AD7656-1/AD7657-1/AD7658-1 using one 96-SCLK transfer,
three 32-SCLK individually framed transfers, or six 16-SCLK
individually framed transfers. Any additional SCLKs applied
after this result in an output of all zeros. When using the serial
interface, tie the RD signal low and leave the unused DOUT line(s)
unconnected.
Whether one, two, or three data output lines are used, if a
particular CONVST pin is not used in the conversion cycle then
all zeros are output in place of the ADC result for the associated
ADCs even though they were not used in the conversion cycle.
This means that if, for example, only CONVST B is pulsed and
one data output pin is in use, then 64 SCLKs are required to
access the results from V3 and V4, but only 32 SCLKs are
required if two or three data output lines are in use.
SERIAL READ OPERATION
Figure 34 shows the timing diagram for reading data from the
AD7656-1/AD7657-1/AD7658-1 when the serial interface is
selected. The SCLK input signal provides the clock source for
the serial interface. The CS signal goes low to access data from
the AD7656-1/AD7657-1/AD7658-1. The falling edge of CS
takes the bus out of three-state and clocks out the MSB of the
16-bit conversion result. The ADCs output 16 bits for each
conversion result; the data stream of the AD7656-1 consists of
16 bits of conversion data, provided MSB first. The data stream
for the AD7657-1 consists of two leading 0s followed by 14 bits
of conversion data, provided MSB first. The data stream for the
AD7658-1 consists of four leading 0s and 12 bits of conversion
data, provided MSB first.
相關PDF資料 |
PDF描述 |
|---|---|
| SP3245ECY-L/TR | IC TXRX RS233 28TSSOP |
| VE-B2Z-MY | CONVERTER MOD DC/DC 2V 20W |
| VE-B6J-IV-S | CONVERTER MOD DC/DC 36V 150W |
| VE-B2Z-MX | CONVERTER MOD DC/DC 2V 30W |
| SP3245ECA-L/TR | IC TXRX RS232 28SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7656YSTZ-REEL | 功能描述:IC ADC 16BIT 6CH 250KSPS 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7657 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
| AD7657-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-/14-/12-Bit ADC |
| AD7657BSTZ | 功能描述:IC ADC 14BIT 6CH 250KSPS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7657BSTZ-1 | 功能描述:IC ADC 14BIT 6CH 250KSPS 64LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。