參數資料
型號: AD7686CCPZRL
廠商: Analog Devices Inc
文件頁數: 27/28頁
文件大?。?/td> 0K
描述: IC ADC 16BIT SAR 500KSPS 10LFCSP
標準包裝: 5,000
系列: PulSAR®
位數: 16
采樣率(每秒): 500k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 21.5mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 10-WFDFN 裸露焊盤,CSP
供應商設備封裝: 10-LFCSP-WD(3x3)
包裝: 帶卷 (TR)
輸入數目和類型: 1 個偽差分,單極
配用: EVAL-AD7686CBZ-ND - BOARD EVALUATION FOR AD7686
AD7686
Rev. B | Page 8 of 28
TERMINOLOGY
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs LSB before the first
code transition. Positive full scale is defined as a level 1 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 25).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level LSB above analog
ground (38.1 μV for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111 . . . 10 to 111 . . . 11) should occur
for an analog voltage 1 LSB below the nominal full scale
(4.999886 V for the 0 V to 5 V range). The gain error is the
deviation of the actual level of the last transition from the ideal
level after the offset is adjusted out.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD by
ENOB = (SINADdB 1.76)/6.02
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in dB.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in dB.
Signal-to-(Noise + Distortion), SINAD
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in dB.
Aperture Delay
It is the measure of the acquisition performance and is the time
between the rising edge of the CNV input and when the input
signal is held for a conversion.
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
相關PDF資料
PDF描述
MS3106F28-20S CONN PLUG 14POS STRAIGHT W/SCKT
T 3484 005 CONN MALE 7POS CABLE MNT R/A
LTC1419CG#TR IC ADC 14BIT 800KSPS SHDN 28SSOP
LTC1279IG#TRPBF IC A/DCONV SAMPLNG W/SHTDN24SSOP
D6FBX CONN RCPT FEMALE 6PIN BLK/SILVER
相關代理商/技術參數
參數描述
AD7686CCPZRL1 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN
AD7686CCPZRL7 功能描述:IC ADC 16BIT SAR 500KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率(每秒):300k 數據接口:并聯 轉換器數目:1 功率耗散(最大):75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端,單極;1 個單端,雙極
AD7686CCPZRL71 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 500 kSPS PulSAR ADC in MSOP/QFN
AD7686CRM 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Serial 10-Pin MSOP Tube
AD7686CRMRL7 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Serial 10-Pin MSOP T/R