- 您現在的位置：買賣IC網 > PDF目錄1982 > AD7693BRMZRL7 (Analog Devices Inc)IC ADC 16BIT 500KSPS 10-MSOP PDF資料下載
參數資料
| 型號： | AD7693BRMZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 500KSPS 10-MSOP |
| 標準包裝： | 1,000 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 500k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 21.5mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
| 配用： | EVAL-AD7693CBZ-ND - BOARD EVALUATION FOR AD7693 |
AD7693
Rev. A | Page 17 of 24
CS MODE, 3-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when a single AD7693 is connected
to an SPI-compatible digital host. The connection diagram is
shown in Figure 34, and the corresponding timing is given in
With SDI tied to VIO, a rising edge on CNV initiates a
conversion, selects the CS mode, and forces SDO to high
impedance. Once a conversion is initiated, it continues until
completion irrespective of the state of CNV. This could be
useful, for instance, to bring CNV low to select other SPI
devices, such as analog multiplexers; however, CNV must be
returned high before the minimum conversion time elapses and
then held high for the maximum possible conversion time to
avoid the generation of the busy signal indicator. When the
conversion is complete, the AD7693 enters the acquisition
phase and powers down. When CNV goes low, the MSB is
output onto SDO. The remaining data bits are clocked by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge will allow a faster
reading rate, provided it has an acceptable hold time. After the
16th SCK falling edge or when CNV goes high (whichever
occurs first), SDO returns to high impedance.
CNV
SCK
SDO
SDI
DATA IN
CLK
CONVERT
VIO
AD7693
06
39
4-
03
3
DIGITAL HOST
Figure 34. CS Mode, 3-Wire Without Busy Indicator
Connection Diagram (SDI High)
SDO
D15
D14
D13
D1
D0
tDIS
SCK
123
14
15
16
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
CNV
CONVERSION
ACQUISITION
tCONV
tCYC
ACQUISITION
SDI = 1
tCNVH
tACQ
tEN
06
39
4-
0
34
Figure 35. CS Mode, 3-Wire Without Busy Indicator Serial Interface Timing (SDI High)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7694ARMZ | IC ADC 16BIT SAR 250KSPS 8MSOP |
| AD7699BCPZRL7 | IC ADC 8CH 16BIT 500KSPS 20LFCSP |
| AD7701BN | IC ADC 16BIT LC2MOS MONO 20-DIP |
| AD7703BN | IC ADC 20BIT LC2MOS 20-DIP |
| AD7706BN | IC ADC 16BIT 3CH 16-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7694 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| AD7694_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP |
| AD7694ARM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7694ARMRL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP |
| AD7694ARMZ | 功能描述:IC ADC 16BIT SAR 250KSPS 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。