- 您現在的位置：買賣IC網 > PDF目錄10684 > AD7790BRMZ (Analog Devices Inc)IC ADC 16BIT SIGMA-DELTA 10-MSOP PDF資料下載
參數資料
| 型號： | AD7790BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/20頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT SIGMA-DELTA 10-MSOP |
| 標準包裝： | 50 |
| 位數： | 16 |
| 采樣率（每秒）： | 120 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 230µW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，雙極 |
| 產品目錄頁面： | 779 (CN2011-ZH PDF) |
AD7790
Data Sheet
Rev. A | Page 18 of 20
REFIN(+) without introducing gain errors in the system. Deriv-
ing the reference input voltage across an external resistor will
mean that the reference input sees a significant external source
impedance. External decoupling on the REFIN pins would not
be recommended in this type of circuit configuration.
VDD MONITOR
Along with converting external voltages, the analog input chan-
nel can be used to monitor the voltage on the VDD pin. When
the CH1 and CH0 bits in the communications register are set to
1, the voltage on the VDD pin is internally attenuated by 5 and
the resultant voltage is applied to the ∑- modulator using an
internal 1.17 V reference for analog to digital conversion. This
is useful because variations in the power supply voltage can be
monitored.
GROUNDING AND LAYOUT
Since the analog inputs and reference inputs of the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode rejec-
tion of the part will remove common-mode noise on these
inputs. The digital filter will provide rejection of broadband
noise on the power supply, except at integer multiples of the
modulator sampling frequency. The digital filter also removes
noise from the analog and reference inputs, provided that these
noise sources do not saturate the analog modulator. As a result,
the AD7790 is more immune to noise interference than a con-
ventional high resolution converter. However, because the
resolution of the AD7790 is so high, and the noise levels from
the AD7790 are so low, care must be taken with regard to
grounding and layout.
The printed circuit board that houses the AD7790 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch
technique is generally best for ground planes because it gives
the best shielding.
It is recommended that the AD7790’s GND pin be tied to the
AGND plane of the system. In any layout, it is important that
the user keep in mind the flow of currents in the system, ensur-
ing that the return paths for all currents are as close as possible
to the paths the currents took to reach their destinations. Avoid
forcing digital currents to flow through the AGND sections of
the layout.
The AD7790’s ground plane should be allowed to run under the
AD7790 to prevent noise coupling. The power supply lines to
the AD7790 should use as wide a trace as possible to provide
low impedance paths and reduce the effects of glitches on the
power supply line. Fast switching signals such as clocks should
be shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run
near the analog inputs. Avoid crossover of digital and analog
signals. Traces on opposite sides of the board should run at
right angles to each other. This will reduce the effects of feed-
through through the board. A microstrip technique is by far the
best, but it is not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes, while signals are placed on the solder side.
Good decoupling is important when using high resolution
ADCs. VDD should be decoupled with 10 F tantalum in parallel
with 0.1 F capacitors to GND. To achieve the best from these
decoupling components, they should be placed as close as
possible to the device, ideally right up against the device. All
logic chips should be decoupled with 0.1 F ceramic capacitors
to DGND.
相關PDF資料 |
PDF描述 |
|---|---|
| AD8611AR-REEL | IC COMP SNGL 4NS ULTRFAST 8-SOIC |
| AD7789BRMZ | IC ADC 24BIT LP 10-MSOP |
| LT1720CS8#TR | IC COMP DUAL R-R 4MA 4.5NS 8SOIC |
| LTC1445IS#TRPBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| CS5530-ISZ | IC ADC 24BIT 1CH W/LNA 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7790BRMZ | 制造商:Analog Devices 功能描述:IC 24-BIT ADC |
| AD7790BRMZ-REEL | 功能描述:IC ADC 16BIT SIGMA-DELTA 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7791 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Buffered 24-Bit Sigma-Delta ADC |
| AD7791BRM | 功能描述:IC ADC 24BIT BUFFERED LP 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7791BRM-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 120sps 24-bit Serial 10-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.12KSPS 24BIT SERL 10MSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。