參數資料
型號: AD7854LARZ-REEL
廠商: Analog Devices Inc
文件頁數: 28/28頁
文件大?。?/td> 0K
描述: IC ADC 12BIT PARALLEL LP 28SOIC
標準包裝: 1,000
位數: 12
采樣率(每秒): 100k
數據接口: 并聯
轉換器數目: 2
功率耗散(最大): 30mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC W
包裝: 帶卷 (TR)
輸入數目和類型: 1 個偽差分,單極;1 個偽差分,雙極
AD7854/AD7854L
REV. B
–9–
CONTROL REGISTER
The arrangement of the control register is shown below. The control register is a write only register and contains 14 bits of data. The
control register is selected by putting two 1s in ADDR1 and ADDR0. The function of the bits in the control register is described
below. The power-up status of all bits is 0.
MSB
ZERO
PMGT1
PMGT0
RDSLT1
RDSLT0
AMODE
CONVST
CALMD
CALSLT1
CALSLT0
STCAL
LSB
Control Register Bit Function Description
Bit
Mnemonic
Comment
13
ZERO
These four bits must be set to 0 when writing to the control register.
12
ZERO
11
ZERO
10
ZERO
9
PMGT1
Power Management Bits. These two bits are used for putting the part into various power-down modes
8
PMGT0
(See Power-Down section for more details).
7
RDSLT1
Theses two bits determine which register is addressed for the read operations. See Table II.
6
RDSLT0
5
AMODE
Analog Mode Bit. This pin allows two different analog input ranges to be selected. A logic 0 in this bit
position selects range 0 to VREF (i.e., AIN(+) – AIN(–) = 0 to VREF). In this range AIN(+) cannot go
below AIN(–) and AIN(–) cannot go below AGND and data coding is straight binary. A logic 1 in this
bit position selects range –VREF/2 to +VREF/2 (i.e., AIN(+) – AIN(–) = –VREF /2 to +VREF/2). AIN(+)
cannot go below AGND, so for this range, AIN(–) needs to be biased to at least +VREF/2 to allow
AIN(+) to go as low as AIN(–) –VREF/2 V. Data coding is twos complement for this range.
4
CONVST
Conversion Start Bit. A logic one in this bit position starts a single conversion, and this bit is automati-
cally reset to 0 at the end of conversion. This bit may also used in conjunction with system calibration
(see Calibration section).
3
CALMD
Calibration Mode Bit. A 0 here selects self-calibration and a 1 selects a system calibration (see Table III).
2
CALSLT1
Calibration Selection Bits and Start Calibration Bit. These bits have two functions.
1
CALSLT0
With the STCAL bit set to 1, the CALSLT1 and CALSLT0 bits determine the type of calibration per-
0
STCAL
formed by the part (see Table III). The STCAL bit is automatically reset to 0 at the end of calibration.
With the STCAL bit set to 0, the CALSLT1 and CALSLT0 bits are decoded to address the calibration
register for read/write of calibration coefficients (see section on the calibration registers for more details).
Table III. Calibration Selection
CALMD
CALSLT1
CALSLT0
Calibration Type
00
0
A full internal calibration is initiated. First the internal DAC is calibrated, then the
internal gain error and finally the internal offset error are removed. This is the default setting.
0
1
First the internal gain error is removed, then the internal offset error is removed.
0
1
0
The internal offset error only is calibrated out.
0
1
The internal gain error only is calibrated out.
10
0
A full system calibration is initiated. First the internal DAC is calibrated, followed by the
system gain error calibration, and finally the system offset error calibration.
1
0
1
First the system gain error is calibrated out followed by the system offset error.
1
0
The system offset error only is removed.
1
The system gain error only is removed.
相關PDF資料
PDF描述
LTC2418CGN#TRPBF IC ADC 24BIT DIFF INPUT 28SSOP
LTC2418CGN#TR IC ADC 24BIT DIFF INPUT 28SSOP
AD7262BSTZ-5 IC ADC 2CH 12BIT PGA/COM 48LQFP
AD7262BCPZ-5 IC ADC 2CH 12BIT PGA/COM 48LFCSP
LTC2418CGN IC ADC 24BIT DIFF INPUT 28SSOP
相關代理商/技術參數
參數描述
AD7854LBR 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter, 12-Bit
AD7854SQ 制造商:Rochester Electronics LLC 功能描述:12-BIT SINGLE CH.PARALLEL ADC I.C. - Bulk
AD7856 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V Single Supply, 8-Channel 14-Bit 285 kSPS Sampling ADC
AD7856AN 制造商:Analog Devices 功能描述:ADC Single SAR 285ksps 14-bit Serial 24-Pin PDIP 制造商:Analog Devices 功能描述:IC 14BIT ADC 7856 DIP24
AD7856ANZ 功能描述:IC ADC 14BIT 8CHAN 5V 24DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率(每秒):20M 數據接口:并聯 轉換器數目:2 功率耗散(最大):155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP(7x7) 包裝:Digi-Reel® 輸入數目和類型:4 個單端,單極;2 個差分,單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6