- 您現在的位置：買賣IC網 > PDF目錄10096 > AD7880CNZ (Analog Devices Inc)IC ADC 12BIT MONO LOW PWR 24DIP PDF資料下載
參數資料
| 型號： | AD7880CNZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT MONO LOW PWR 24DIP |
| 標準包裝： | 15 |
| 位數： | 12 |
| 采樣率（每秒）： | 66k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 50mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 24-PDIP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極 |
AD7880
–12–
REV. 0
as a function of time for such operation. The total conversion
time for each cycle is 11
× 15 s (where 15 s is the time taken
for a single conversion) corresponding to 1.65
× 10–4 secs.
Hence:
Average Power
= PowerCONVERTING + PowerPOWER-DOWN
= {20 mW
× (1.65 × 10–4)/(10)}
+ {2 mW
× (9.9998)/(10)}
= 2.029 mW
AD7880 DATA ACQUISITION LAYOUT
Figure 24 shows the AD7880 in a data acquisition circuit. The
corresponding printed circuit board (PCB) layout and
silkscreen are shown in Figures 25 to 27.
The only additional component required for a full data acquisi-
tion system is an antialiasing filter. There is a component grid
provided near the analog input on the PCB which may be used
for such a filter or any other input conditioning circuitry. To fa-
cilitate this option there is a shorting link (labeled LK1 on the
PCB) on the analog input track. With LK1 in place, the analog
input connects to the buffer amplifier driving the AD7880.
With LK1 removed, a wire link is needed to connect the analog
input to the PCB component grid.
INTERFACE CONNECTIONS
The data acquisition board contains a parallel connection port
labeled SKT4. This is a 26-contact IDC Connector and pro-
vides for direct microprocessor connection to the board. This
connector, the pinout of which is shown in Figure 23, contains
all data, control and status signals of the AD7880 (with the ex-
ception of the CONVST and the CLKIN inputs both of which
are provided via SKT2 and SKT3 respectively). It also contains
decoded R/W and STRB inputs which are necessary for inter-
facing to many microprocessors including the TMS320C25 and
the Motorola 68000 series. Link LK7 selects RD directly or al-
ternatively, the decoded version. Note that the AD7880 CS in-
put must be decoded prior to the AD7880 evaluation board.
SKT1, SKT2 and SKT3 are three sub-miniature connectors
(SMC) which provide input connections for the analog input,
the CONVST input and the CLKIN input. Three different in-
put ranges can be accepted by the AD7880 each of which is
configured by selecting shorting plug options A, B or C of LK4.
Position A corresponds to the 0 V to 5 V unipolar configuration
of Figure 5, position B corresponds to the bipolar
±5 V configu-
ration of Figure 7 and position C allows for a 0 V to +10 V uni-
polar range as shown in Figure 6.
POWER SUPPLY CONNECTIONS
The PCB requires a single +5 V power supply (labeled VDD).
Good decoupling allows this supply to drive the AD7880 VDD
which also drives the VREF input as well as the op amp power
supply. In circumstances where bipolar
±5 V or a unipolar 0 V
to 10 V input ranges are required, provision has been allowed
for the connection of separate op amp power supplies (
±15 V,
±12 V, ±5 V, etc.) to V+ and V–. LK2 and LK3 shorting links
allow for the selection of user defined op amp power supplies or
the on-board single +5 V supply.
LINK OPTIONS
There are seven link options which must be set before using the
board. These are outlined below:
LK1
Connects the analog input to a buffer amplifier. The
analog input may also be connected to a component
grid for signal conditioning.
LK2, LK3 Allows for various op amp power supplies to be
used to drive the input buffer of the AD7880. Ex-
ternal supplies may be connected to V+ and V–.
Alternatively, the AD7880’s +5 V system supply
and AGND can be selected to drive a single supply
op amp.
LK4
Configures the various analog input ranges, 0 V to
5 V, 0 V to 10 V or
±5 V.
LK5
Selects reference input to VREF of AD7880. Nor-
mally connected to VDD. An external reference
could also be wired in.
LK6
Selects power-down or sleep mode. The shorting
plug is connected to VDD for normal operation.
LK7
Connects the AD7880 RD input directly to the RD
input of SKT4 or to a decoded STRB and R/W
input. This shorting plug setting depends on the
microprocessor, e.g., the TMS320C25 requires a
decoded RD signal.
DB10
DB8
DB6
DB4
DB2
DB0
GND
R/W
RD
CS
1
3
5
7
9
13
15
17
19
25
23
21
11
N/C
2
4
6
8
10
14
16
18
20
26
24
22
12
DB11
DB9
DB7
DB5
DB3
DB1
GND
STRB
BUSY
N/C
5V
+
5V
+
BUSY
Figure 23. SKT4, IDC Connector Pinout
COMPONENT LIST
IC1
Op Amp*
IC2
AD7880 Analog-to-Digital Converter
IC3
74HC00 Quad NAND Gate
C1, C3, C5
10
F Capacitors
C2, C4, C6, C7
0.1
F Capacitors
R1, R2
10 k
Pull-up Resistors
LK1, LK2, LK3
Shorting Links
LK4, LK5, LK6
LK7
SKT1, SKT2, SKT3 Sub-Miniature Connectors
Vendor No: Sealectro 50-051-0000 (Socket)
Vendor No: Sealectro 50-007-0000 (Plug)
SKT4
26-Contact (2 Row) IDC Connector
NOTE
*See ANALOG INPUT BUFFERING section.
.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26K-MX-F2 | CONVERTER MOD DC/DC 40V 75W |
| VI-24B-IU-F4 | CONVERTER MOD DC/DC 95V 200W |
| D38999/26FC8PE | CONN PLUG 8POS STRAIGHT W/PINS |
| IDT72215LB15TFI8 | IC FIFO 512X18 SYNC 15NS 64QFP |
| VI-23M-IX-B1 | CONVERTER MOD DC/DC 10V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7880CQ | 制造商:Analog Devices 功能描述:ADC Single SAR 66ksps 12-bit Parallel 24-Pin CDIP 制造商:Rochester Electronics LLC 功能描述:12 BIT ADC IC - Bulk |
| AD7880CR | 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7880CR-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 66ksps 12-bit Parallel 24-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 66KSPS 12-BIT PARALLEL 24SOIC W - Tape and Reel |
| AD7880CRZ | 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7880CRZ-REEL | 功能描述:IC ADC 12BIT MONO LP 24-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。