- 您現在的位置：買賣IC網 > PDF目錄1985 > AD7985BCPZ-RL7 (Analog Devices Inc)IC ADC 16B 2.5MSPS PULSR 20LFCSP PDF資料下載
參數資料
| 型號： | AD7985BCPZ-RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16B 2.5MSPS PULSR 20LFCSP |
| 標準包裝： | 1,500 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 2.5M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 33mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個偽差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7985
Rev. A | Page 15 of 28
ANALOG INPUTS
Figure 24 shows an equivalent circuit of the input structure of
the AD7985.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs, IN+ and IN. Care must be taken to ensure that
the analog input signal does not exceed the reference input
voltage (REF) by more than 0.3 V. If the analog input signal
exceeds this level, the diodes become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 130 mA maximum. However, if the supplies of the
input buffer (for example, the V+ and V supplies of the buffer
amplifier in Figure 23) are different from those of REF, the
analog input signal may eventually exceed the supply rails by
more than 0.3 V. In such a case (for example, an input buffer
with a short circuit), the current limitation can be used to
protect the part.
CPIN
REF
RIN
CIN
D1
D2
IN+ OR IN–
REFGND
07947-
008
Figure 24. Equivalent Analog Input Circuit
The analog input structure allows the sampling of the true
differential signal between IN+ and IN. By using these
differential inputs, signals common to both inputs are rejected.
During the acquisition phase, the impedance of the analog inputs
(IN+ and IN) can be modeled as a parallel combination of
Capacitor CPIN and the network formed by the series connection
of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically
400 and is a lumped component composed of serial resistors
and the on resistance of the switches. CIN is typically 30 pF and
is mainly the ADC sampling capacitor.
During the sampling phase, where the switches are closed, the
input impedance is limited to CPIN. RIN and CIN make a one-pole,
low-pass filter that reduces undesirable aliasing effects and
limits noise.
When the source impedance of the driving circuit is low, the
AD7985 can be driven directly. Large source impedances
significantly affect the ac performance, especially THD. The
dc performances are less sensitive to the input impedance. The
maximum source impedance depends on the amount of THD
that can be tolerated. The THD degrades as a function of the
source impedance and the maximum input frequency.
DRIVER AMPLIFIER CHOICE
Although the AD7985 is easy to drive, the driver amplifier must
meet the following requirements:
The noise generated by the driver amplifier must be kept as
low as possible to preserve the SNR and transition noise
performance of the AD7985. The noise from the driver is
filtered by the AD7985 analog input circuit’s one-pole, low-
pass filter, made by RIN and CIN, or by the external filter, if
one is used. Because the typical noise of the AD7985 is
50 V rms, the SNR degradation due to the amplifier is
+
=
2
)
(
2
π
50
log
20
N
3dB
LOSS
Ne
f
SNR
where:
f–3dB is the input bandwidth, in megahertz, of the AD7985
(20 MHz) or the cutoff frequency of the input filter, if
one is used.
N is the noise gain of the amplifier (for example, 1 in buffer
configuration).
eN is the equivalent input noise voltage of the op amp, in
nV/√Hz.
For ac applications, the driver should have a THD perfor-
mance commensurate with that of the AD7985.
For multichannel multiplexed applications, the driver
amplifier and the AD7985 analog input circuit must settle
for a full-scale step onto the capacitor array at a 16-bit level
(0.0015%, 15 ppm). In the data sheet of the driver amplifier,
settling at 0.1% to 0.01% is more commonly specified. This
value may differ significantly from the settling time at a
16-bit level and should be verified prior to driver selection.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
Very low noise and high frequency
Low noise and high frequency
Ultralow noise and high frequency
Low power and high frequency
相關PDF資料 |
PDF描述 |
|---|---|
| AD7986BCPZ-RL7 | IC ADC 18BIT 2MSPS SAR 20LFCSP |
| AD7988-1BRMZ-RL7 | IC ADC 16BIT SRL 100KSPS 10MSOP |
| AD7991YRJZ-1RL | IC ADC 12BIT 4CH I2C SOT23-8 |
| AD7992BRMZ-1REEL | IC ADC 12BIT 2CHAN I2C 10MSOP |
| AD7994BRUZ-1 | IC ADC 12BIT 4CHAN I2C 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7986 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 nV/√Hz, Low Power |
| AD7986BCPZ | 功能描述:IC ADC 18BIT 2MSPS SAR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7986BCPZ-RL7 | 功能描述:IC ADC 18BIT 2MSPS SAR 20LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7986BCPZ-U1 | 制造商:Analog Devices 功能描述:16-BIT, 10MSPS PULSAR DIFFERENTIAL ADC - Rail/Tube |
| AD7986XCPZ-U1 | 制造商:Analog Devices 功能描述:16-BIT, 10MSPS PULSAR DIFFERENTIAL ADC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。