參數資料
型號: AD8139ACPZ-REEL
廠商: Analog Devices Inc
文件頁數: 11/25頁
文件大?。?/td> 0K
描述: IC AMP DIFF R-R LN LDIST 8LFCSP
標準包裝: 5,000
放大器類型: 差分
電路數: 1
輸出類型: 差分,滿擺幅
轉換速率: 800 V/µs
-3db帶寬: 410MHz
電流 - 輸入偏壓: 2.25µA
電壓 - 輸入偏移: 150µV
電流 - 電源: 24.5mA
電流 - 輸出 / 通道: 100mA
電壓 - 電源,單路/雙路(±): 4.5 V ~ 12 V,±2.25 V ~ 6 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-VFDFN 裸露焊盤,CSP
供應商設備封裝: 8-LFCSP-VD(3x3)
包裝: 帶卷 (TR)
AD8139
Rev. B | Page 18 of 24
THEORY OF OPERATION
The AD8139 is a high speed, low noise differential amplifier
fabricated on the Analog Devices second-generation eXtra Fast
Complementary Bipolar (XFCB) process. It is designed to
provide two closely balanced differential outputs in response to
either differential or single-ended input signals. Differential
gain is set by external resistors, similar to traditional voltage-
feedback operational amplifiers. The common-mode level of
the output voltage is set by a voltage at the VOCM pin and is
independent of the input common-mode voltage. The AD8139
has an H-bridge input stage for high slew rate, low noise, and
low distortion operation and rail-to-rail output stages that
provide maximum dynamic output range. This set of features
allows for convenient single-ended-to-differential conversion, a
common need to take advantage of modern high resolution
ADCs with differential inputs.
TYPICAL CONNECTION AND DEFINITION OF
TERMS
Figure 59 shows a typical connection for the AD8139, using
matched external RF/RG networks. The differential input
terminals of the AD8139, VAP and VAN, are used as summing
junctions. An external reference voltage applied to the VOCM
terminal sets the output common-mode voltage. The two
output terminals, VOP and VON, move in opposite directions in a
balanced fashion in response to an input signal.
+
VAP
VAN
VON
VOP
+
VO, dm
RL, dm
AD8139
CF
RF
RG
CF
RF
VIP
VOCM
VIN
04
67
9-
0
50
Figure 59. Typical Connection
The differential output voltage is defined as
VO, dm = VOP VON
(1)
Common-mode voltage is the average of two voltages. The
output common-mode voltage is defined as
2
ON
OP
cm
O,
V
+
=
(2)
Output Balance
Output balance is a measure of how well VOP and VON are
matched in amplitude and how precisely they are 180° out of
phase with each other. It is the internal common-mode feedback
loop that forces the signal component of the output common-mode
towards zero, resulting in the near perfectly balanced differential
outputs of identical amplitude and exactly 180° out of phase. The
output balance performance does not require tightly matched
external components, nor does it require that the feedback factors
of each loop be equal to each other. Low frequency output balance
is limited ultimately by the mismatch of an on-chip voltage divider,
which is trimmed for optimum performance.
Output balance is measured by placing a well-matched resistor
divider across the differential voltage outputs and comparing
the signal at the midpoint of the divider with the magnitude of
the differential output. By this definition, output balance is
equal to the magnitude of the change in output common-mode
voltage divided by the magnitude of the change in output
differential-mode voltage:
dm
O,
cm
O,
V
Balance
Output
Δ
=
(3)
The block diagram of the AD8139 in Figure 60 shows the
external differential feedback loop (RF/RG networks and the
differential input transconductance amplifier, GDIFF) and the
internal common-mode feedback loop (voltage divider across
VOP and VON and the common-mode input transconductance
amplifier, GCM). The differential negative feedback drives the
voltages at the summing junctions VAN and VAP to be essentially
equal to each other.
VAN = VAP
(4)
The common-mode feedback loop drives the output common-
mode voltage, sampled at the midpoint of the two 500 Ω resistors,
to equal the voltage set at the VOCM terminal. This ensures that
2
dm
O,
OCM
OP
V
+
=
(5)
and
2
dm
O,
OCM
ON
V
=
(6)
VOP
VOCM
GO
GDIFF
GO
GCM
10pF
500
VON
MIDSUPPLY
+
VAN
VIN
VIP
VAP
RG
RF
04
67
9-
0
51
Figure 60. Block Diagram
相關PDF資料
PDF描述
69192-122HLF BERGSTIK II DR STRAIGHT RET
2089-250-BT1LF SURGE ARRESTOR GDT 2500V AXIAL
644861-3 CONN HEADER VERT .100 3POS TIN
69192-226HLF BERGSTIK II DR STRAIGHT RET
644861-2 CONN HEADER VERT .100 2POS TIN
相關代理商/技術參數
參數描述
AD8139ACPZ-REEL7 功能描述:IC AMP DIFF R-R LN LDIST 8LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR
AD8139AR 制造商:Analog Devices 功能描述:
AD8139ARD 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):4.5 V ~ 38 V,±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:帶卷 (TR)
AD8139ARD-EBZ 功能描述:BOARD EVAL FOR AD8139ARD RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
AD8139ARD-REEL 功能描述:IC AMP DIFF R-R LN LDIST 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件