- 您現在的位置：買賣IC網 > PDF目錄6027 > AD8228BRZ (Analog Devices Inc)IC AMP INST PREC LDRIFT LN 8SOIC PDF資料下載
參數資料
| 型號： | AD8228BRZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP INST PREC LDRIFT LN 8SOIC |
| 產品培訓模塊： | Current Sense Amplifiers Instrumentation Amplifiers Performance |
| 標準包裝： | 98 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 轉換速率： | 2.5 V/µs |
| -3db帶寬： | 650kHz |
| 電流 - 輸入偏壓： | 400pA |
| 電壓 - 輸入偏移： | 50µV |
| 電流 - 電源： | 850µA |
| 電流 - 輸出 / 通道： | 18mA |
| 電壓 - 電源，單路/雙路(±)： | 4.6 V ~ 36 V，±2.3 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 產品目錄頁面： | 771 (CN2011-ZH PDF) |
AD8228
Rev. 0 | Page 17 of 24
REFERENCE TERMINAL
The output voltage of the AD8228 is developed with respect to
the potential on the reference terminal. This is useful when the
output signal needs to be offset to a precise midsupply level. For
example, a voltage source can be tied to the REF pin to level-shift
the output so that the AD8228 can drive a single-supply ADC. The
REF pin is protected with ESD diodes and should not exceed
either +VS or VS by more than 0.3 V.
For best performance, source impedance to the REF terminal
should be kept below 1 Ω. As shown in Figure 41, the reference
terminal, REF, is at one end of a 10 kΩ resistor. Additional imped-
ance at the REF terminal adds to this 10 kΩ resistor and results
in amplification of the signal connected to the positive input.
The amplification from the additional RREF can be computed by
(
)
REF
R
+
×
kΩ
20
kΩ
10
2
Only the positive signal path is amplified; the negative path is
unaffected. This uneven amplification degrades the CMRR of
the amplifier.
INCORRECT
V
CORRECT
AD8228
OP1177
+
–
V
07
03
5-
00
5
REF
AD8228
REF
Figure 43. Driving the Reference
LAYOUT
The AD8228 is a high precision device. To ensure optimum
performance at the PCB level, care must be taken in the design
of the board layout. The AD8228 pins are arranged in a logical
manner to aid in this task.
8
7
6
5
1
2
3
4
–IN
G1
G2
+VS
VOUT
REF
–VS
+IN
TOP VIEW
(Not to Scale)
AD8228
07
03
5-
0
44
Figure 44. Pinout Diagram
Common-Mode Rejection Ratio over Frequency
The AD8228 has a higher CMRR over frequency than typical
in-amps, which gives it greater immunity to disturbances such
as line noise and its associated harmonics. The AD8228 pinout
was designed so that the board designer can take full advantage
of this performance with a well-implemented layout.
Poor layout can cause some of the common-mode signal to be
converted to a differential signal before it reaches the in-amp.
Such conversions occur when one input path has a frequency
response that is different from the other. To keep CMRR across
frequency high, input source impedance and capacitance of each
path should be closely matched. Additional source resistance in
the input path (for example, for input protection) should be placed
close to the in-amp inputs, which minimizes their interaction
with parasitic capacitance from the PCB traces.
Parasitic capacitance at the gain setting pins can also affect
CMRR over frequency. If the board design has a component at
the gain setting pins (for example, a switch or jumper), the part
should be chosen so that the parasitic capacitance is as small as
possible.
Power Supplies
A stable dc voltage should be used to power the instrumentation
amplifier. Noise on the supply pins can adversely affect perform-
for more information.
A 0.1 μF capacitor should be placed as close as possible to each
supply pin. As shown in Figure 45, a 10 μF tantalum capacitor
can be used farther away from the part. In most cases, it can be
shared by other precision integrated circuits.
AD8228
+VS
+IN
–IN
LOAD
REF
0.1F
10F
0.1F
10F
–VS
VOUT
07
03
5-
00
6
Figure 45. Supply Decoupling, REF, and Output Referred to Local Ground
相關PDF資料 |
PDF描述 |
|---|---|
| OP284EPZ | IC OPAMP GP R-R 4.25MHZ LN 8DIP |
| AD9632ARZ | IC OPAMP VF ULDIST 70MA 8SOIC |
| AD713JRZ-16-REEL7 | IC OPAMP BIFET QUAD PREC 16SOIC |
| LT1014ISW#PBF | IC OPAMP PRECISION QUAD 16-SOIC |
| LT1882CS#PBF | IC OPAMP QUAD R-R PICO/IN 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8228BRZ-R7 | 功能描述:IC AMP INST PREC LDRIFT LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| AD8228BRZ-RL | 功能描述:IC AMP INST PREC LDRIFT LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD8229 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1nV/√Hz Low Noise 210°C Instrumentation Amplifier |
| AD8229HDZ | 功能描述:IC AMP INSTR LOW NOISE 8-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD8229HRZ | 功能描述:IC AMP INST LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:TS1854A View All Specifications 標準包裝:50 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.25 V/µs 增益帶寬積:630kHz -3db帶寬:- 電流 - 輸入偏壓:16nA 電壓 - 輸入偏移:1000µV 電流 - 電源:162µA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。