參數資料
型號： AD9233BCPZ-105
廠商： Analog Devices Inc
文件頁數： 21/44頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 105MSPS 48-LFCSP
標準包裝： 1
位數： 12
采樣率（每秒）： 105M
數據接口： 串行，SPI?
轉換器數目： 1
功率耗散（最大）： 350mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
供應商設備封裝： 48-LFCSP-VQ（7x7）
包裝： 托盤
輸入數目和類型： 2 個單端，單極；1 個差分，單極
配用： AD9233-125EBZ-ND - BOARD EVALUATION FOR AD9233
AD9233
Rev. A | Page 28 of 44
EVALUATION BOARD
The AD9233 evaluation board provides all of the support
circuitry required to operate the ADC in its various modes and
configurations. The converter can be driven differentially
through a double balun configuration (default) or through the
AD8352 differential driver. The ADC can also be driven in a
single-ended fashion. Separate power pins are provided to
isolate the DUT from the AD8352 drive circuitry. Each input
configuration can be selected by proper connection of various
components. Figure 59 shows the typical bench characterization
setup used to evaluate the ac performance of the AD9233.
It is critical that the signal sources used for the analog input and
clock have very low phase noise (<1 ps rms jitter) to realize the
optimum performance of the converter. Proper filtering of the
analog input signal to remove harmonics and lower the inte-
grated or broadband noise at the input is also necessary to achieve
the specified noise performance.
See Figure 60 to Figure 70 for the complete schematics and
layout diagrams that demonstrate the routing and grounding
techniques that should be applied at the system level.
POWER SUPPLIES
This evaluation board comes with a wall-mountable switching
power supply that provides a 6 V, 2 A maximum output. Simply
connect the supply to the rated 100 V ac to 240 V ac wall outlet
at 47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter
jack that connects to the PCB at P500. Once on the PC board,
the 6 V supply is fused and conditioned before connecting to
five low dropout linear regulators that supply the proper bias to
each of the various sections on the board. When operating the
evaluation board in a nondefault condition, L501, L503, L504,
L508, and L509 can be removed to disconnect the switching
power supply. This enables the user to bias each section of the
board independently. Use P501 to connect a different supply for
each section.
Although at least one 1.8 V supply is needed with a 1 A current
capability for AVDD_DUT and DRVDD_DUT, it is recom-
mended that separate supplies be used for analog and digital.
To operate the evaluation board using the AD8352 option, a
separate 5.0 V analog supply is needed. The 5.0 V supply, or
AMP_VDD, should have a 1 A current capability. To operate
the evaluation board using the alternate SPI options, a separate
3.3 V analog supply is needed in addition to the other supplies.
The 3.3 V supply (AVDD_3.3V) should have a 1 A current
capability as well. Solder Jumpers J501, J502, and J505 allow the
user to combine these supplies. See Figure 64 for more details.
INPUT SIGNALS
When connecting the clock and analog source, use clean signal
generators with low phase noise, such as Rohde & Schwarz SMHU
or Agilent HP8644 signal generators or the equivalent. Use one
meter long, shielded, RG-58, 50 Ω coaxial cables for making
connections to the evaluation board. Enter the desired frequency
and amplitude for the ADC. Typically, most ADI evaluation
boards can accept a ~2.8 V p-p or 13 dBm sine wave input for
the clock. When connecting the analog input source, it is
recommended to use a multipole, narrow-band, band-pass
filter with 50 Ω terminations. Analog Devices uses TTE, Allen
Avionics, and K&L types of band-pass filters. Connect the filter
directly to the evaluation board, if possible.
OUTPUT SIGNALS
The parallel CMOS outputs interface directly with Analog
Devices’ standard single-channel FIFO data capture board
(HSC-ADC-EVALB-SC). For more information on the FIFO
boards and their optional settings, visit www.analog.com/FIFO.
ROHDE & SCHWARZ,
SMHU,
2V p-p SIGNAL
SYNTHESIZER
ROHDE & SCHWARZ,
SMHU,
2V p-p SIGNAL
SYNTHESIZER
BAND-PASS
FILTER
AIN
CLK
12-BIT
PARALLEL
CMOS
USB
CONNECTION
AD9233
EVALUATION BOARD
HSC-ADC-EVALB-SC
FIFO DATA
CAPTURE
BOARD
PC
RUNNING
ADC
ANALYZER
AND SPI
USER
SOFTWARE
1.8V
–+
A
V
DD_DUT
VD
L
D
R
V
DD_DUT
GN
D
GN
D
–+
5.0V
GN
D
A
M
P_
VD
D
2.5V
6V DC
2A MAX
WALL OUTLET
100V TO 240V AC
47Hz TO 63Hz
SWITCHING
POWER
SUPPLY
–+
GN
D
3.3V
A
V
DD_3.
3V
–+
GN
D
3.3V
–+
VC
C
GN
D
3.3V
SPI
0
54
92-
084
Figure 59. Evaluation Board Connection
相關PDF資料
PDF描述
VI-J5N-MW-F3 CONVERTER MOD DC/DC 18.5V 100W
EXP-0911/04/S CONN PLUG 4POS IP68 W/SOCKETS
VI-J5N-MW-F1 CONVERTER MOD DC/DC 18.5V 100W
97-3108B-18-12S CONN PLUG RT ANG 6POS W/SOCKETS
LTC2265CUJ-12#PBF IC ADC 12BIT SER/PAR 65M 40-QFN
相關代理商/技術參數
參數描述
AD9233BCPZ-125 功能描述:IC ADC 12BIT 80/105/125 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD9233BCPZ-80 功能描述:IC ADC 12BIT 80MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD9233BCPZRL7-105 功能描述:IC ADC 12BIT 105MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9233BCPZRL7-125 功能描述:IC ADC 12BIT 125MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9233BCPZRL7-80 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit, 80 MSPS/105 MSPS/125 MSPS, 1.8 V Analog-to-Digital Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*