- 您現在的位置：買賣IC網 > PDF目錄8577 > AD9785BSVZRL (Analog Devices Inc)IC DAC 12BIT 800MSPS 100TQFP PDF資料下載
參數資料
| 型號： | AD9785BSVZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 41/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 12BIT 800MSPS 100TQFP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1,000 |
| 系列： | TxDAC® |
| 位數： | 12 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 450mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-TQFP 裸露焊盤 |
| 供應商設備封裝： | 100-TQFP-EP（14x14） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 800M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9785/AD9787/AD9788
Rev. A | Page 46 of 64
Table 33 lists the register settings required to enable the PN
code mode synchronization feature.
Table 33. Register Settings for Enabling PN Code Mode
Register
Bit
Parameter
Value
0x01
[13]
PN code sync enable
1
[12]
Sync mode select
1
[11]
Pulse sync enable
0
0x03
[31:27]
Correlate Threshold
[4:0]
10000
[26]
SYNC_I enable
1
[25]
SYNC_O enable
0 (slave devices)
1 (master device)
[10]
Set high
1
To verify that the devices have successfully synchronized, read
back the sync lock status bit on all devices (Register 0x09,
Bit 10). The sync lock status bit should read back as 1 on all
devices. Next, read back the sync lock lost status bit on all
devices (Register 0x09, Bit 11). The sync lock lost status bit
should read back as 0 on all devices. To clear the sync lock lost
status bit, set the clear lock indicator bit to 1, followed by a 0
(Register 0x09, Bit 12).
Because the SYNC_O signal generated by the master is spread
over many bits, this method of synchronization is very robust.
Any individual bits that may become corrupted or somehow
misread by the slave device usually have no effect on the
synchronization of the device. If the devices do not reliably
synchronize, there are several options for correcting the situation.
The SYNC_O Delay [4:0] value (Register 0x03, Bits [15:11]) on
the master device can be used to adjust the timing in 80 ps steps
effective across all devices. In addition, the SYNC_O polarity bit
(Register 0x03, Bit 9) on the master device can be set to provide
a delay of one half the DACCLK period. The SYNC_I Delay [4:0]
bits (Register 0x03, Bits [23:19]) can be used to adjust the
timing on a single slave device in 80 ps steps.
The Correlate Threshold [4:0] value (Register 0x03,
Bits [31:27]) indicates how closely the code of the received
SYNC_I signal is to the expected code. A high threshold
requires a closer match of the encoded signal to set the
sync lock status bit; a lower value reduces the matching
requirements to set the sync lock status bit.
Increasing the Correlate Threshold [4:0] value makes the part
more resistant to false synchronization locks but requires a
lower bit error rate on the SYNC_I input to maintain locked
status. Decreasing the Correlate Threshold [4:0] value makes
the part more susceptible to false synchronization locks, but
maintains a locked status in the face of a higher bit error rate
on the SYNC_I input (that is, it is more noise resistant). The
recommended value for Correlate Threshold [4:0] is the default
value of 16.
INTERRUPT REQUEST OPERATION
The IRQ pin (Pin 71) acts as an alert that the device has
experienced a timing error and that it should be queried (by
reading Register 0x09) to determine the exact fault condition.
The IRQ pin is an open-drain, active low output. The IRQ pin
should be pulled high external to the device. This pin may be
tied to the IRQ pins of other devices with open-drain outputs to
wire-OR these pins together.
There are two different error flags that can trigger an interrupt
request: a data timing error or a sync timing error. By default,
when either or both of these error flags are set, the IRQ pin is
active low. Either or both of these error flags can be masked to
prevent them from activating an interrupt on the IRQ pin.
The error flags are latched and remain active until the flag bits
are overwritten.
相關PDF資料 |
PDF描述 |
|---|---|
| HFA1135IBZ | IC OPAMP CFA 360MHZ LP 8-SOIC |
| LTC2754BIUKG-16#TRPBF | IC DAC 16BIT QUAD IOUT 52-QFN |
| HA3-5020-5Z | IC AMP VIDEO CFA 100MHZ 8-DIP |
| HFA1105IBZ | IC OPAMP CFA 330MHZ LP 8-SOIC |
| VI-B1N-MU | CONVERTER MOD DC/DC 18.5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9785-DPG2-EBZ | 功能描述:BOARD EVALUATION FOR AD9785 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9785-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9785 制造商:Analog Devices 功能描述:DUAL 12B, 1GSPS D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9786 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 200 MSPS/500 MSPS TxDAC+ with 2】/4】/8】 Interpolation and Signal Processing |
| AD9786BSV | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP 制造商:Analog Devices 功能描述:IC 16BIT DAC SMD 9786 TQFP80 |
| AD9786BSVRL | 制造商:Analog Devices 功能描述:DAC 1-CH Interpolation Filter 16-bit 80-Pin TQFP EP T/R |
發布緊急采購，3分鐘左右您將得到回復。