參數資料
型號： ADC12041
廠商： National Semiconductor Corporation
英文描述： 12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter(12位216 kHz采樣A/D轉換器)
中文描述： 12位帶符號216 kHz的采樣模擬到數字轉換器（12位216 kHz的采樣的A / D轉換器）
文件頁數： 23/28頁
文件大?。?/td> 591K
代理商： ADC12041
Features and Operating Modes
(Continued)
degrade the conversion result. In the SYNC-IN mode, only
the rising edge of the SYNC signal will begin a conversion
cycle. The RDY signal will go low when the conversion cycle
is done. The acquisition time is controlled by the SYNC sig-
nal. The acquisition period begins after the falling edge of the
RDY signal. The input is sampled until the rising edge of the
SYNC pulse, at which time the signal will be held and con-
version begins. The RDY signal will go low when the conver-
sion is done and a new operational command may be written
into the Configuration register at this time, if needed. With
the START command in the Configuration register, a read
from the ADC12041 will place the entire conversion result
stored in the Data register on the data bus and the rising
edge of the read pulse will force the RDY signal high.
STANDBY COMMAND
8-bit mode: A write to the ADC12041 should clear the BW bit
and issue the Standby command.
13-bit mode: A write to the ADC12041 should set the BW bit
and issue the Standby command.
RESET
The RESET command places the ADC12041 into a ready
state and forces the RDY signal low. The RESET command
can be used to interrupt the ADC12041 while it is performing
a conversion, full-calibration or auto-zero cycle. It can also
be used to get the ADC12041 out of the standby mode.
Analog Application Information
REFERENCE VOLTAGE
The ADC12041 has two reference inputs, V
+ and V
.
They define the zero to full-scale range of the analog input
signals over which 4095 positive and 4096 negative codes
exist. The reference inputs can be connected to span the en-
tire supply voltage range (V
REF
= AGND, V
REF
+ = V
A
+) or
they can be connected to different voltages when other input
spans are required. The reference inputs of the ADC12041
have transient capacitive switching currents. The voltage
sources driving V
+ and V
must have very low output
impedence and noise and must be adequately bypassed.
The circuit in Figure 20 is an example of a very stable refer-
ence source.
The ADC12041 can be used in either ratiometric or absolute
reference applications. In ratiometric systems, the analog in-
put voltage is proportional to the voltage used for the ADC’s
reference voltage. This technique relaxes the system refer-
ence requirements because the analog input voltage moves
with the ADC’s reference. The system power supply can be
used as the reference voltage by connecting the V
REF
+ pin
to V
A
+ and the V
REF
pin to AGND. For absolute accuracy,
where the analog input voltage varies between very specific
voltage limits, a time and temperature stable voltage source
can be connected to the reference inputs. Typically, the ref-
erence voltage’s magnitude will require an initial adjustment
to null reference voltage induced full-scale errors.
The reference voltage inputs are not fully differential. The
ADC12041
will
not
generate
(V
+) – (V
) is below 1V. Figure 19 shows the allow-
able relationship between V
REF
+ and V
REF
.
correct
conversions
if
OUTPUT DIGITAL CODE VERSUS ANALOG INPUT
VOLTAGE
The ADC12041’s fully differential 12-bit + sign ADC gener-
ates a two’s complement output that is found by using the
equation shown below:
Round off the result to the nearest integer value between
-4096 and 4095.
DS012441-43
FIGURE 19. V
REF
Operating Range
A
www.national.com
23
相關PDF資料
PDF描述
ADC12041CIV 12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
ADC12041CIMSA NiCd/NiMH/Lead-Acid Gas Gauge For High Discharge Rates (>10A), Pgmable Offset Error & Load Comp. 16-SOIC 0 to 70
ADC12048EVAL 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048CIVF 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
ADC12048 12-Bit Plus Sign 216 kHz 8-Channel Sampling Analog-to-Digital Converter
相關代理商/技術參數
參數描述
ADC12041AZ WAF 制造商:Texas Instruments 功能描述:
ADC12041CIMSA 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
ADC12041CIMSAX 功能描述:IC ADC 12BIT 28-SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
ADC12041CIV 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
ADC12041CIVX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit Plus Sign 216 kHz Sampling Analog-to-Digital Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*