- 您現在的位置：買賣IC網 > PDF目錄19387 > ADSP-21489KSWZ-3B (Analog Devices Inc)IC CCD SIGNAL PROCESSOR 176LQFP PDF資料下載
參數資料
| 型號： | ADSP-21489KSWZ-3B |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/68頁 |
| 文件大小： | 0K |
| 描述： | IC CCD SIGNAL PROCESSOR 176LQFP |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | EBI/EMI，DAI，I²C，SPI，SPORT，UART/USART |
| 時鐘速率： | 350MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 5Mb |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.10V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 176-LQFP 裸露焊盤 |
| 供應商設備封裝： | 176-LQFP-EP（24x24） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Rev. B
|
Page 23 of 68
|
March 2013
Note the definitions of the clock periods that are a function of
CLKIN and the appropriate ratio control shown in Table 18. All
of the timing specifications for the ADSP-2148x peripherals are
defined in relation to tPCLK. See the peripheral specific section
for each peripheral’s timing information.
Figure 4 shows core to CLKIN relationships with external oscil-
lator or crystal. The shaded divider/multiplier blocks denote
where clock ratios can be set through hardware or software
using the power management control register (PMCTL). For
more information, see the ADSP-214xx SHARC Processor Hard-
ware Reference.
Power-Up Sequencing
The timing requirements for processor startup are given in
Table 19. While no specific power-up sequencing is required
between VDD_EXT and VDD_INT, there are some considerations
that system designs should take into account.
No power supply should be powered up for an extended
period of time (> 200 ms) before another supply starts to
ramp up.
If the VDD_INT power supply comes up after VDD_EXT, any
pin, such as RESETOUT and RESET, may actually drive
momentarily until the VDD_INT rail has powered up.
Systems sharing these signals on the board must determine
if there are any issues that need to be addressed based on
this behavior.
Note that during power-up, when the VDD_INT power supply
comes up after VDD_EXT, a leakage current of the order of three-
state leakage current pull-up, pull-down may be observed on
any pin, even if that is an input only (for example the RESET
pin) until the VDD_INT rail has powered up.
Table 18. Clock Periods
Timing
Requirements
Description
tCK
CLKIN Clock Period
tCCLK
Processor Core Clock Period
tPCLK
Peripheral Clock Period = 2 × tCCLK
tSDCLK
SDRAM Clock Period = (tCCLK) × SDCKR
Table 19. Power Up Sequencing Timing Requirements (Processor Startup)
Parameter
Min
Max
Unit
Timing Requirements
tRSTVDD
RESET Low Before VDD_EXT or VDD_INT On
0
ms
tIVDDEVDD
VDD_INT On Before VDD_EXT
–200
+200
ms
tCLKVDD
1
CLKIN Valid After VDD_INT and VDD_EXT Valid
0
200
ms
tCLKRST
CLKIN Valid Before RESET Deasserted
102
μs
tPLLRST
PLL Control Setup Before RESET Deasserted
203
μs
Switching Characteristic
tCORERST
4, 5
Core Reset Deasserted After RESET Deasserted
4096 × tCK + 2 × tCCLK
1 Valid VDD_INT and VDD_EXT assumes that the supplies are fully ramped to their nominal values (it does not matter which supply comes up first). Voltage ramp rates can vary
from microseconds to hundreds of milliseconds depending on the design of the power supply subsystem.
2 Assumes a stable CLKIN signal, after meeting worst-case startup timing of crystal oscillators. Refer to your crystal oscillator manufacturer's data sheet for startup time. Assume
a 25 ms maximum oscillator startup time if using the XTAL pin and internal oscillator circuit in conjunction with an external crystal.
3 Based on CLKIN cycles.
4 Applies after the power-up sequence is complete. Subsequent resets require a minimum of four CLKIN cycles for RESET to be held low in order to properly initialize and
propagate default states at all I/O pins.
5 The 4096 cycle count depends on tSRST specification in Table 21. If setup time is not met, one additional CLKIN cycle may be added to the core reset time, resulting in 4097
cycles maximum.
相關PDF資料 |
PDF描述 |
|---|---|
| EBM08DCSH | CONN EDGECARD 16POS DIP .156 SLD |
| ACM36DRXS | CONN EDGECARD 72POS DIP .156 SLD |
| ABM36DRXS | CONN EDGECARD 72POS DIP .156 SLD |
| EBM08DCSD | CONN EDGECARD 16POS DIP .156 SLD |
| ABC36DRYN-S13 | CONN EDGECARD 72POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21489KSWZ-4A | 功能描述:IC CCD SIGNAL PROCESSOR 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21489KSWZ-4B | 功能描述:IC CCD SIGNAL PROCESSOR 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-21489KSWZ-5B | 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAG 制造商:Analog Devices 功能描述:450 MHZ SHARC W/ STATIC VOLTAGE SCALING - Trays 制造商:Analog Devices 功能描述:Digital Signal Processors & Controllers - DSP, DSC High Perf 4th Generation 制造商:Analog Devices 功能描述:450 MHz SHARC w/ Static Voltage Scaling |
| ADSP-21489KSWZENGA | 制造商:Analog Devices 功能描述:SHARC PROCESSOR - Trays |
| ADSP-21532S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-21532S: Blackfin? DSP Preliminary Data Sheet (Rev. PrD. 3/03) |
發布緊急采購，3分鐘左右您將得到回復。