參數資料
型號: ADSP-TS201SYBPZ050
廠商: Analog Devices Inc
文件頁數: 13/48頁
文件大?。?/td> 0K
描述: IC PROCESSOR 500MHZ 576-SBGA
標準包裝: 1
系列: TigerSHARC®
類型: 定點/浮點
接口: 主機接口,連接端口,多處理器
時鐘速率: 500MHz
非易失內存: 外部
芯片上RAM: 3MB
電壓 - 輸入/輸出: 2.50V
電壓 - 核心: 1.05V
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 576-BBGA 裸露焊盤
供應商設備封裝: 576-BGA-ED(25x25)
包裝: 托盤
配用: ADZS-TS201S-EZLITE-ND - KIT LITE EVAL FOR ADSP-TS201S
Rev. C
|
Page 20 of 48
|
December 2006
ADSP-TS201S
STRAP PIN FUNCTION DESCRIPTIONS
Some pins have alternate functions at reset. Strap options set
DSP operating modes. During reset, the DSP samples the strap
option pins. Strap pins have an internal pull-up or pull-down
for the default value. If a strap pin is not connected to an over-
driving external pull-up, pull-down, or logic load, the DSP
samples the default value during reset. If strap pins are
connected to logic inputs, a stronger external pull-up or pull-
down may be required to ensure default value depending on
leakage and/or low level input current of the logic load. To set a
mode other than the default mode, connect the strap pin to a
sufficiently stronger external pull-up or pull-down. Table 16
lists and describes each of the DSP’s strap pins.
When default configuration is used, no external resistor is
needed on the strap pins. To apply other configurations, a
500
Ω resistor connected to VDD_IO is required. If providing
external pull-downs, do not strap these pins directly to VSS; the
strap pins require 500
Ω resistor straps.
All strap pins are sampled on the rising edge of RST_IN (deas-
sertion edge). Each pin latches the strapped pin state (state of
the strap pin at the rising edge of RST_IN). Shortly after deas-
sertion of RST_IN, these pins are reconfigured to their normal
functionality.
These strap pins have an internal pull-down resistor, pull-up
resistor, or no-resistor (three-state) on each pin. The resistor
type, which is connected to the I/O pad, depends on whether
RST_IN is active (low) or if RST_IN is deasserted (high).
Table 17 shows the resistors that are enabled during active reset
and during normal operation.
Table 16. Pin Definitions—I/O Strap Pins
Signal
Type (at
Reset)
On Pin …
Description
EBOOT
I
(pd_0)
BMS
EPROM Boot.
0 = boot from EPROM immediately after reset (default)
1 = idle after reset and wait for an external device to boot DSP
through the external port or a link port
IRQEN
I
(pd)
BM
Interrupt Enable.
0 = disable and set IRQ3–0 interrupts to edge-sensitive after
reset (default)
1 = enable and set IRQ3–0 interrupts to level-sensitive
immediately after reset
LINK_DWIDTH
I
(pd)
TMR0E
Link Port Input Default Data Width.
0 = 1-bit (default)
1 = 4-bit
SYS_REG_WE
I
(pd_0)
BUSLOCK
SYSCON and SDRCON Write Enable.
0 = one-time writable after reset (default)
1 = always writable
TM1
I
(pu)
L1BCMPO
Test Mode 1. Do not overdrive default value during reset.
TM2
I
(pu)
L2BCMPO
Test Mode 2. Do not overdrive default value during reset.
TM3
I
(pu)
L3BCMPO
Test Mode 3. Do not overdrive default value during reset.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Table 17. Strap Pin Internal Resistors—Active Reset
(RST_IN = 0) vs. Normal Operation (RST_IN = 1)
Pin
RST_IN = 0
RST_IN = 1
BMS
(pd_0)
(pu_0)
BM
(pd)
Driven
TMR0E
(pd)
Driven
BUSLOCK
(pd_0)
(pu_0)
L1BCMPO
(pu)
Driven
L2BCMPO
(pu)
Driven
L3BCMPO
(pu)
Driven
pd = internal pull-down 5 k
Ω; pu = internal pull-up 5 kΩ;
pd_0 = internal pull-down 5 k
Ω on DSP ID = 0;
pu_0 = internal pull-up 5 k
Ω on DSP ID = 0
相關PDF資料
PDF描述
FAN2500S28X IC REG LDO 2.8V .1A SOT-23-5
171-015-213R011 CONN DB15 FEMALE DIP SLD NICKEL
VE-2WY-CW-F4 CONVERTER MOD DC/DC 3.3V 66W
VE-2WR-CY-F4 CONVERTER MOD DC/DC 7.5V 50W
TPSC106K020R0700 CAP TANT 10UF 20V 10% 2312
相關代理商/技術參數
參數描述
ADSP-TS202SABP-050 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 500MHz 500MIPS 576-Pin TEBGA 制造商:Analog Devices 功能描述:DSP FLOATING PT 32BIT 500MHZ 500MIPS 576PIN TEBGA - Trays
ADSP-TS202SABP-05X 制造商:Analog Devices 功能描述:
ADSP-TS202SABP-X 制造商:Analog Devices 功能描述:
ADSP-TS202SABPZ050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:TigerSHARC® 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C,McASP,McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA,F(xiàn)CBGA 供應商設備封裝:548-FCBGA(27x27) 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-TS203SABP-050 功能描述:IC DSP FLOAT/FIXED 500MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤