參數資料
型號： ADV7180BSTZ
廠商： Analog Devices Inc
文件頁數： 70/116頁
文件大小： 0K
描述： IC VIDEO DECODER SDTV 64-LQFP
產品變化通告： ADV7180 Metal Mask Edit 22/Oct/2009
設計資源： Low Cost Differential Video Receiver Using ADA4851 Amplifier and ADV7180 Video Decoder (CN0060)
Low Cost Video Multiplexer for Video Switching Using ADA4853-2 Op Amp with Disable Function (CN0076)
標準包裝： 1
類型： 視頻解碼器
應用： 數碼相機，手機，便攜式視頻
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
產品目錄頁面： 788 (CN2011-ZH PDF)
配用： EVAL-ADV7180LQEBZ-ND - BOARD EVALUATION ADV7180
EVAL-ADV7180LFEBZ-ND - BOARD EVAL FOR ADV7180 LFCSP
Data Sheet
ADV7180
Rev. I | Page 57 of 116
VDP_TTXT_TYPE_MAN_ENABLE, Enable Manual
Selection of Teletext Type, Address 0x60[2], User Sub Map
Setting VDP_TTXT_TYPE_MAN_ENABLE to 0 (default), the
manual programming of the teletext type is disabled.
Setting VDP_TTXT_TYPE_MAN_ENABLE to 1, the manual
programming of the teletext type is enabled.
VDP_TTXT_TYPE_MAN[1:0], Specify the Teletext Type,
Address 0x60[1:0], User Sub Map
These bits specify the teletext type to be decoded. These bits are
functional only if VDP_TTXT_TYPE_MAN_ENABLE is set to 1.
Table 72. VDP_TTXT_TYPE_MAN Function
VDP_TTXT_
TYPE_MAN[1:0]
625/50 (PAL)
525/60 (NTSC)
00 (default)
Teletext-ITU-BT.653-
625/50-A
Reserved
01
Teletext-ITU-BT.653-
625/50-B (WST)
Teletext-ITU-BT.653-
525/60-B
10
Teletext-ITU-BT.653-
625/50-C
Teletext-ITU-BT.653-
525/60-C or EIA516
(NABTS)
11
Teletext-ITU-BT.653-
625/50-D
Teletext-ITU-BT.653-
525/60-D
VDP Ancillary Data Output
Reading the data back via I2C may not be feasible for VBI data
standards with high data rates (for example, teletext). An alternative
is to place the sliced data in a packet in the line blanking of the
digital output CCIR656 stream. This is available for all standards
sliced by the VDP module.
When data is sliced on a given line, the corresponding ancillary
data packet is placed immediately after the next EAV code that
occurs at the output (that is, data sliced from multiple lines are
not buffered up and then emitted in a burst). Note that, due to
the vertical delay through the comb filters, the line number on
which the packet is placed differs from the line number on
which the data was sliced.
The user can enable or disable the insertion of VDP results that
have been decoded into the 656 ancillary streams by using the
ADF_ENABLE bit.
ADF_ENABLE, Enable Ancillary Data Output Through
656 Stream, Address 0x62[7], User Sub Map
Setting ADF_ENABLE to 0 (default) disables the insertion of
VBI decoded data into the ancillary 656 stream.
Setting ADF_ENABLE to 1 enables the insertion of VBI
decoded data into the ancillary 656 stream.
The user may select the data identification word (DID) and the
secondary data identification word (SDID) through programming
the ADF_DID[4:0] and ADF_SDID[5:0] bits, respectively.
ADF_DID[4:0], User-Specified Data ID Word in Ancillary
Data, Address 0x62[4:0], User Sub Map
This bit selects the data ID word to be inserted into the ancillary
data stream with the data decoded by the VDP.
The default value of ADF_DID[4:0] is 10101.
ADF_SDID[5:0], User-Specified Secondary Data ID Word
in Ancillary Data, Address 0x63[5:0], User Sub Map
These bits select the secondary data ID word to be inserted in
the ancillary data stream with the data decoded by the VDP.
The default value of ADF_SDID[5:0] is 101010.
DUPLICATE_ADF, Enable Duplication/Spreading of
Ancillary Data over Y and C Buses, Address 0x63[7], User
Sub Map
This bit determines whether the ancillary data is duplicated over
both Y and C buses or if the data packets are spread between
the two channels.
When DUPLICATE_ADF to 0 (default) is set, the ancillary data
packet is spread across the Y and C data streams.
When DUPLICATE_ADF to 1 is set, the ancillary data packet is
duplicated on the Y and C data streams.
ADF_MODE[1:0], Determine the Ancillary Data Output
Mode, Address 0x62[6:5], User Sub Map
These bits determine whether the ancillary data output mode is
in byte mode or nibble mode.
Table 73. ADF_MODE
ADF_MODE[1:0]
Description
00 (default)
Nibble mode
01
Byte mode, no code restrictions
10
Byte mode, but 0x00 and 0xFF prevented
(0x00 replaced by 0x01, 0xFF replaced by 0xFE)
11
Reserved
相關PDF資料
PDF描述
VI-BWR-MX-F3 CONVERTER MOD DC/DC 7.5V 75W
VE-2W3-IW-F1 CONVERTER MOD DC/DC 24V 100W
ADV7611BSWZ-P IC RCVR HDMI 165MHZ LP 64LQFP
MAX3483ECPA+ IC TXRX RS485/422 250KBPS 8-DIP
VI-BWR-MX-F1 CONVERTER MOD DC/DC 7.5V 75W
相關代理商/技術參數
參數描述
ADV7180BSTZ 制造商:Analog Devices 功能描述:Video IC
ADV7180BSTZ-REEL 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND
ADV7180KCP32Z 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KCP32Z-RL 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KST48Z 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*