- 您現在的位置：買賣IC網 > PDF目錄294981 > AGL10005-FG484 FPGA, 1000000 GATES, 250 MHz, PBGA484 PDF資料下載
參數資料
| 型號： | AGL10005-FG484 |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 1000000 GATES, 250 MHz, PBGA484 |
| 封裝： | 13 X 13 MM, 1 MM PITCH, FBGA-144 |
| 文件頁數： | 141/204頁 |
| 文件大小： | 2800K |
| 代理商： | AGL10005-FG484 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁當前第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁
IGLOO Low-Power Flash FPGAs with Flash*Freeze Technology
A d v an c ed v0 . 1
2-27
Signal Descriptions for RAM512X185
RAM512X18
has
slightly
different
behavior
than
RAM4K9, as it has dedicated read and write ports.
WW and RW
These signals enable the RAM to be configured in one of
the two allowable aspect ratios (Table 2-9).
WD and RD
These are the input and output data signals, and they
are 18 bits wide. When a 512×9 aspect ratio is used for
write, WD[17:9] are unused and must be grounded. If
this aspect ratio is used for read, RD[17:9] are undefined.
WADDR and RADDR
These are read and write addresses, and they are nine
bits wide. When the 256×18 aspect ratio is used for write
or read, WADDR[8] or RADDR[8] are unused and must be
grounded.
WCLK and RCLK
These signals are the write and read clocks, respectively.
They can be clocked on the rising or falling edge of
WCLK and RCLK.
WEN and REN
These
signals
are
the
write
and
read
enables,
respectively. They are both active low by default. These
signals can be configured as active high.
RESET
This active low signal resets the control logic, forces the
output hold state registers to zero, disables reads and
writes from the SRAM block, and clears the data hold
registers when asserted. It does not reset the contents of
the memory array.
While the RESET signal is active, read and write
operations are disabled. As with any asynchronous reset
signal, care must be taken not to assert it too close to the
edges of active read and write clocks. Refer to the tables
beginning with Table 3-148 on page 3-94 for the
specifications.
PIPE
This signal is used to specify pipelined read on the
output. A LOW on PIPE indicates a nonpipelined read,
and the data appears on the output in the same clock
cycle. A HIGH indicates a pipelined read, and data
appears on the output in the next clock cycle.
Clocking
The dual-port SRAM blocks are only clocked on the rising
edge. SmartGen allows falling-edge-triggered clocks by
adding inverters to the netlist, hence achieving dual-port
SRAM blocks that are clocked on either edge (rising or
falling). For dual-port SRAM, each port can be clocked on
either edge and/or by separate clocks by port.
IGLOO devices support inversion (bubble pushing)
throughout the FPGA architecture, including the clock
input to the SRAM modules. Inversions added to the
SRAM clock pin on the design schematic or in the HDL
code will be automatically accounted for during design
compile without incurring additional delay in the clock
path.
The two-port SRAM can be clocked on the rising or
falling edge of WCLK and RCLK.
If negative-edge RAM and FIFO clocking is selected for
memory macros, clock edge inversion management
(bubble pushing) is automatically used within the IGLOO
development tools, without performance penalty.
Modes of Operation
There are two read modes and one write mode:
Read Nonpipelined (synchronous—1 clock edge):
In the standard read mode, new data is driven
onto the RD bus in the same clock cycle following
RA and REN valid. The read address is registered
on the read port clock active edge, and data
appears at RD after the RAM access time. Setting
PIPE to OFF enables this mode.
Read Pipelined (synchronous—2 clock edges): The
pipelined mode incurs an additional clock delay
from address to data but enables operation at a
much higher frequency. The read address is
registered on the read port active clock edge, and
the read data is registered and appears at RD after
the second read clock edge. Setting PIPE to ON
enables this mode.
Write (synchronous—1 clock edge): On the write
clock active edge, the write data is written into
the SRAM at the write address when WEN is HIGH.
The setup times of the write address, write
enables, and write data are minimal with respect
to the write clock. Write and read transfers are
described with timing requirements in the "DDR
5. The AGL030 device does not support SRAM or FIFO.
Table 2-9 Aspect Ratio Settings for WW[1:0]
WW[1:0]
RW[1:0]
D×W
01
512×9
10
256×18
00, 11
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| AGL10005-FGG144I | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FGG144 | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FGG256I | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FGG256 | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FGG484I | FPGA, 1000000 GATES, 250 MHz, PBGA484 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AGL1000V2-CS144 | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144ES | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144PP | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS281 | 功能描述:IC FPGA 1KB FLASH 1M 281-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
發布緊急采購，3分鐘左右您將得到回復。