- 您現在的位置：買賣IC網 > PDF目錄294981 > AGL10005-FGG484 FPGA, 1000000 GATES, 250 MHz, PBGA484 PDF資料下載
參數資料
| 型號： | AGL10005-FGG484 |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 1000000 GATES, 250 MHz, PBGA484 |
| 封裝： | 13 X 13 MM, 1 MM PITCH, ROHS COMPLIANT, FBGA-144 |
| 文件頁數： | 140/204頁 |
| 文件大?。?/td> | 2800K |
| 代理商： | AGL10005-FGG484 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁當前第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁
IGLOO Low-Power Flash FPGAs with Flash*Freeze Technology
2- 26
Advanced v0.1
Signal Descriptions for RAM4K94
The following signals are used to configure the RAM4K9
memory element:
WIDTHA and WIDTHB
These signals enable the RAM to be configured in one of
four allowable aspect ratios (Table 2-6).
BLKA and BLKB
These signals are active low and will enable the
respective ports when asserted. When a BLKx signal is
deasserted, that port’s outputs hold the previous value.
WENA and WENB
These signals switch the RAM between read and write
modes for the respective ports. A LOW on these signals
indicates a write operation, and a HIGH indicates a read.
CLKA and CLKB
These are the clock signals for the synchronous read and
write operations. These can be driven independently or
with the same driver.
PIPEA and PIPEB
These signals are used to specify pipelined read on the
output.
A
LOW
on
PIPEA
or
PIPEB
indicates
a
nonpipelined read, and the data appears on the
corresponding output in the same clock cycle. A HIGH
indicates a pipelined read, and data appears on the
corresponding output in the next clock cycle.
WMODEA and WMODEB
These signals are used to configure the behavior of the
output when the RAM is in write mode. A LOW on these
signals makes the output retain data from the previous
read. A HIGH indicates pass-through behavior, wherein
the data being written will appear immediately on the
output. This signal is overridden when the RAM is being
read.
RESET
This active low signal resets the control logic, forces the
output hold state registers to zero, disables reads and
writes from the SRAM block, and clears the data hold
registers when asserted. It does not reset the contents of
the memory array.
While the RESET signal is active, read and write
operations are disabled. As with any asynchronous reset
signal, care must be taken not to assert it too close to the
edges of active read and write clocks. Refer to the tables
beginning with Table 3-147 on page 3-93 for the
specifications.
ADDRA and ADDRB
These are used as read or write addresses, and they are 12
bits wide. When a depth of less than 4 k is specified, the
unused high-order bits must be grounded (Table 2-7).
DINA and DINB
These are the input data signals, and they are nine bits
wide. Not all nine bits are valid in all configurations.
When a data width less than nine is specified, unused
high-order signals must be grounded (Table 2-8).
DOUTA and DOUTB
These are the nine-bit output data signals. Not all nine
bits are valid in all configurations. As with DINA and
DINB, high-order bits may not be used (Table 2-8). The
output data on unused pins is undefined.
4. The AGL030 device does not support SRAM or FIFO.
Table 2-6 Allowable Aspect Ratio Settings for
WIDTHA[1:0]
WIDTHA[1:0]
WIDTHB[1:0]
D×W
00
4k×1
01
2k×2
10
1k×4
11
512×9
Note: The aspect ratio settings are constant and cannot be
changed on the fly.
Table 2-7 Address Pins Unused/Used for Various
Supported Bus Widths
D×W
ADDRx
Unused
Used
4k×1
None
[11:0]
2k×2
[11]
[10:0]
1k×4
[11:10]
[9:0]
512×9
[11:9]
[8:0]
Note: The "x" in ADDRx implies A or B.
Table 2-8 Unused/Used Input and Output Data Pins for
Various Supported Bus Widths
D×W
DINx/DOUTx
Unused
Used
4k×1
[8:1]
[0]
2k×2
[8:2]
[1:0]
1k×4
[8:4]
[3:0]
512×9
None
[8:0]
Note: The "x" in DINx or DOUTx implies A or B.
相關PDF資料 |
PDF描述 |
|---|---|
| AGLN030V2-FCSG81 | FPGA, PBGA81 |
| AGLN030V2-FQN48 | FPGA, PQCC48 |
| AGLN030V2-FQN68 | FPGA, PQCC68 |
| AGLN030V2-FQNG48 | FPGA, PQCC48 |
| AGLN030V2-FQNG68 | FPGA, PQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AGL1000V2-CS144 | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144ES | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144PP | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS281 | 功能描述:IC FPGA 1KB FLASH 1M 281-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
發布緊急采購，3分鐘左右您將得到回復。