- 您現在的位置：買賣IC網 > PDF目錄366405 > AM29DL642G90MDI (ADVANCED MICRO DEVICES INC) 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Simultaneous Read/Write Flash Memo PDF資料下載
參數資料
| 型號： | AM29DL642G90MDI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Simultaneous Read/Write Flash Memo |
| 中文描述： | 8M X 16 FLASH 3.3V PROM MODULE, 90 ns, PBGA63 |
| 封裝： | 10.95 X 11.95 MM, 0.80 MM PITCH, FBGA-63 |
| 文件頁數： | 28/54頁 |
| 文件大?。?/td> | 828K |
| 代理商： | AM29DL642G90MDI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
26
Am29DL642G
June 10, 2005
P R E L I M I N A R Y
COMMAND DEFINITIONS
Writing specific address and data commands or se-
quences into the command register initiates device op-
erations. Table 13 defines the valid register command
sequences. Writing
incorrect
address and data val-
ues
or writing them in the
improper sequence
resets
the device to reading array data.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the
AC Characteristics
section for timing
diagrams.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. Each bank is ready to read array data
after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command,
the corresponding bank enters the erase-sus-
pend-read mode, after which the system can read
data from any non-erase-suspended sector within the
same bank. The system can read array data using the
standard read timing, except that if it reads at an ad-
dress within erase-suspended sectors, the device out-
puts status data. After completing a programming
operation in the Erase Suspend mode, the system
may once again read array data with the same excep-
tion. See the
Erase Suspend/Erase Resume Com-
mands
section for more information.
The system
must
issue the reset command to return a
bank to the read (or erase-suspend-read) mode if DQ5
goes high during an active program or erase opera-
tion, or if the bank is in the autoselect mode. See the
next section,
Reset Command
, for more information.
See also
Requirements for Reading Array Data
in the
Device Bus Operations
section for more information.
The
Read-Only Operations
table provides the read pa-
rameters, and
Figure 13
shows the timing diagram.
Reset Command
Writing the reset command resets the banks to the
read or erase-suspend-read mode. Address bits are
don’t cares for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the bank to which the sys-
tem was writing to the read mode. Once erasure be-
gins, however, the device ignores reset commands
until the operation is complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the bank to
which the system was writing to the read mode. If the
program command sequence is written to a bank that
is in the Erase Suspend mode, writing the reset
command returns that bank to the erase-sus-
pend-read mode. Once programming begins, however,
the device ignores reset commands until the operation
is complete.
The reset command may be written between the se-
quence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must be written to return to the read mode. If a bank
entered the autoselect mode while in the Erase Sus-
pend mode, writing the reset command returns that
bank to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the banks to the
read mode (or erase-suspend-read mode if that bank
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and device codes,
and determine whether or not a sector is protected.
The autoselect command sequence may be written to
an address within a bank that is either in the read or
erase-suspend-read mode. The autoselect command
may not be written while the device is actively pro-
gramming or erasing in the other bank.
The autoselect command sequence is initiated by first
writing two unlock cycles. This is followed by a third
write cycle that contains the bank address and the au-
toselect command. The bank then enters the autose-
lect mode. The system may read any number of
autoselect codes without reinitiating the command se-
quence.
Table 13 shows the address and data requirements.
To determine sector protection information, the system
must write to the appropriate bank address (BA) and
sector address (SA). Table 2 shows the address range
and bank number associated with each sector.
The system must write the reset command to return to
the read mode (or erase-suspend-read mode if the
bank was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The SecSi Sector region provides a secured data area
containing a random, sixteen-byte electronic serial
number (ESN). The system can access the SecSi
Sector region by issuing the three-cycle Enter SecSi
Sector command sequence. The device continues to
access the SecSi Sector region until the system is-
sues the four-cycle Exit SecSi Sector command se-
相關PDF資料 |
PDF描述 |
|---|---|
| AM29DL800BB120ED | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
| AM29DL800BT120WBK | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
| AM29DL800BT70ED | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
| AM29DL800BT70EF | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
| AM29DL800BT70EK | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29DL800BB-120WBD | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 8Mbit 1M/512K x 8bit/16bit 120ns 48-Pin FBGA |
| AM29DL800BB-70SI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 8MBIT 1MX8/512KX16 70NS 44SOIC - Trays |
| AM29DL800BB-90EI | 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 8Mbit 1M/512K x 8bit/16bit 90ns 48-Pin TSOP |
| AM29DL800BT-120EC | 制造商:Spansion 功能描述:SPZAM29DL800BT-120EC TB 120n EOL160610 |
| AM29DL800BT-120WBC | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。