28
Am29SL160C
November 1, 2004
Command Definitions
Table 12.
Am29SL160C Command Definitions
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE# pulse, whichever happens
later.
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A19–A12 uniquely select any sector.
Notes:
1.
2.
See
Table 1, on page 11
for description of bus operations.
All values are in hexadecimal.
3.
Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
4.
Data bits DQ15–DQ8 are don’t cares in byte mode.
5.
Unless otherwise noted, address bits A19–A11 are don’t cares.
6.
No unlock or command cycles required when in read mode.
7.
The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when in the autoselect mode, or if DQ5 goes high (while providing
status information).
8.
The fourth cycle of the autoselect command sequence is a read
cycle.
9.
The data is 00h for an unprotected sector and 01h for a protected
sector. Data bits DQ15–DQ8 are don’t care. See the Autoselect
Command Sequence section for more information.
10. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
11. The Unlock Bypass Reset command is required to return to the
read mode when in the unlock bypass mode.
12. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
13. The Erase Resume command is valid only during the Erase
Suspend mode.
14. Command is valid when device is ready to read array data or
when device is in autoselect mode.
Command
Sequence
(Note 1)
C
Bus Cycles (Notes 2–5)
Third
Addr
Data
First
Second
Addr
Fourth
Fifth
Sixth
Addr
RA
XXX
555
AAA
Data
RD
F0
Data
Addr
Data
Addr
Data
Addr
Data
Read (Note 6)
Reset (Note 7)
1
1
A
Manufacturer ID
Word
Byte
4
AA
2AA
555
55
555
AAA
90
X00
01
Device ID
(Top Boot/Bottom
Boot)
Word
4
555
AA
2AA
55
555
90
X01
22E4/
22E7
E4/E7
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
Word
Byte
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
XXX
555
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
2AA
555
PA
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
555
AAA
X02
X03
X06
SecSi Sector Factory
Protect
4
AA
55
90
Sector Protect Verify
(Note 9)
4
AA
55
90
(SA)X02
(SA)X04
Enter SecSi Sector Region
3
AA
55
88
Exit SecSi Sector Region
4
AA
55
90
XXX
00
Program
4
AA
55
A0
PA
PD
Unlock Bypass
3
AA
55
20
Unlock Bypass Program (Note 10)
2
2
A0
PD
Unlock Bypass Reset (Note 11)
BA
555
AAA
555
AAA
BA
BA
55
AA
90
XXX
2AA
555
2AA
555
00
Chip Erase
Word
Byte
Word
Byte
6
AA
55
555
AAA
555
AAA
80
555
AAA
555
AAA
AA
2AA
555
2AA
555
55
555
AAA
10
Sector Erase
6
AA
55
80
AA
55
SA
30
Erase Suspend (Note 12)
Erase Resume (Note 13)
1
1
B0
30
CFI Query (Note 14)
Word
Byte
1
98