- 您現在的位置：買賣IC網 > PDF目錄379669 > AN957 (Electronic Theatre Controls, Inc.) Measuring HEXFETCharacteristics PDF資料下載
參數資料
| 型號： | AN957 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Measuring HEXFETCharacteristics |
| 中文描述： | 測量HEXFETCharacteristics |
| 文件頁數： | 5/13頁 |
| 文件大小： | 235K |
| 代理商： | AN957 |
AN-957
(v.Int)
Figure 8.
Drain-source resistance
Figure 9.
Source-drain voltage (diode)
7. R
DS(on)
This is the drain-source resistance at 25°C with V
GS
= 10V. Since R
DS(on)
is temperature-dependent, it is important to minimize
heating of the junction during the test. A pulse test is therefore used to measure this parameter. The test is set up in the following
manner:
1. Connect the device as follows: gate to “B”, drain to “C”, source to “E”.
2. Set the MAX PEAK VOLTS to 15 V.
3. Set the SERIES RESISTOR to 0.3 Ohms.
4. The POLARITY switch should be set to NPN.
5. The MODE switch should be set to “NORM”.
6. Set the STEP AMPLITUDE to 1V.
7. Set NUMBER OF STEPS to 10.
8. Set OFFSET MULT to 0.
9. The CURRENT LIMIT should be set to 500 mA.
10. The STEP MULTIPLIER button should be OUT—that is, 0.1X not
selected.
11. On the PULSED STEPS selector, the 80 microsec button should be IN
(or the 300 microsec, if the 80 is not available).
12. On the RATE selector, the 0.5X button should be IN.
13. Set VERTICAL CURRENT/DIV at 1 amp/div (IRF630). This scale
should be chosen according to the on-resistance of the device being
tested
14. Set the CONNECTION SELECTOR to the “STEP GEN” position in
the “EMITTER GROUNDED” sector.
15. Connect the device using the LEFT/RIGHT switch and raise the
VARIABLE COLLECTOR SUPPLY voltage until the desired value of
drain current is obtained. R
DS(on)
is obtained from the trace by reading
the peak values of current and voltage (see Figures 7and 8).
R
DS(on)
= VDS/ID.
Logic level devices would have different settings for 6, 7 and 8 so that the
on-resistance is measured at the specified gate voltage
8. V
SD
This is the source-drain voltage at rated current with VGS = 0. It is the forward voltage drop of the body-drain diode when
carrying rated current. If pulsed mode testing is required, use high current test fixture.
1. Connect the device as follows: gate to “B”, drain to “C”, source to “E”.
2. Set the MAX PEAK VOLTS to 15V.
3. Set the SERIES RESISTOR at 1.4 ohms or a value sufficiently low
that rated current can be obtained.
4. Set POLARITY to PNP.
5. Set MODE to "NORM".
6. The 80 microsec button of the PULSED STEPS selector should be IN
(or the 300 microsec, if the 80 is not available).
7. The CONNECTION SELECTOR should be set to the "SHORT"
position in the “EMITTER GROUNDED” sector.
8. HORIZONTAL VOLTS/DIV should be on 200 mV/div.
9. VERTICAL CURRENT DIV should be on 1 amp/div.
10. The DISPLAY button should be set to invert.
1
A
PER
V
E
R
T
DIV
500
mV
PER
H
O
R
Z
DIV
1
A
PER
V
E
R
T
DIV
500
mV
PER
H
O
R
Z
DIV
1
A
PER
V
E
R
T
DIV
200
mV
PER
H
O
R
Z
DIV
Figure 7.
Drain-source resistance, pulsed mode
To Order
Index
相關PDF資料 |
PDF描述 |
|---|---|
| AN985B | CARDBUS-TO-ETHERNET LAN CONTROLLER |
| AND124G | Standard LED T-1 Package (3 mm) |
| AND180CRP | GaAlAs Red Light Emission T-1 3/4 Package (5 mm) |
| AND190HW | Ultra Bright LED Lamps |
| AND233GCP | GaP Green Light Emission Special Shape Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN-960 | 制造商:AD 制造商全稱:Analog Devices 功能描述:RS-485/RS-422 CIRCUIT IMPLEMENTATION GUIDE |
| AN960010L | 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN96010 | 制造商:n/a 功能描述:Ships in 2 days 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN960-10 | 制造商:AN# - MILITARY 功能描述: 制造商: 功能描述: 制造商:undefined 功能描述: |
| AN9601016 | 制造商:n/a 功能描述:Ships in 2 days |
發布緊急采購，3分鐘左右您將得到回復。