- 您現在的位置：買賣IC網 > PDF目錄295111 > AT25080N-10SC-1.8 (ATMEL CORP) SPI Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT25080N-10SC-1.8 |
| 廠商： | ATMEL CORP |
| 元件分類： | PROM |
| 英文描述： | SPI Serial EEPROMs |
| 中文描述： | 1K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 279K |
| 代理商： | AT25080N-10SC-1.8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁
6
AT25080/160/320/640
0675F–08/01
Serial Interface
Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25080/160/320/640
always operates as a slave.
TRANSMITTER/RECEIVER: The AT25080/160/320/640 has separate pins designated for
data transmission (SO) and reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be
received. This byte contains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into the
AT25080/160/320/640, and the serial output pin (SO) will remain in a high impedance state
until the falling edge of CS is detected again. This will reinitialize the serial communication.
CHIP SELECT: The AT25080/160/320/640 is selected when the CS pin is low. When the
device is not selected, data will not be accepted via the SI pin, and the serial output pin (SO)
will remain in a high impedance state.
HOL D : T he HO LD pi n is used in conju n ct ion wit h t h e CS pin t o sele ct t h e
AT25080/160/320/640. When the device is selected and a serial sequence is underway,
HOLD can be used to pause the serial communication with the master device without resetting
the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is low.
To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK
may still toggle during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the
high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when
held high. When the WP pin is brought low and WPEN bit is “1”, all write operations to the sta-
tus register are inhibited. WP going low while CS is still low will interrupt a write to the status
register. If the internal write cycle has already been initiated, WP going low will have no effect
on any write operation to the status register. The WP pin function is blocked when the WPEN
bit in the status register is "0". This will allow the user to install the AT25080/160/320/640 in a
system with the WP pin tied to ground and still be able to write to the status register. All WP
pin functions are enabled when the WPEN bit is set to “1”.
相關PDF資料 |
PDF描述 |
|---|---|
| AT25080N-10SI | SPI Serial EEPROMs |
| AT25080-10PI-2.7 | SPI Serial EEPROMs |
| AT25080N-10SI-1.8 | SPI Serial EEPROMs |
| AT25080N-10SI-2.7 | SPI Serial EEPROMs |
| AT25080A-10PI-2.7 | SPI Serial EEPROMs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25080N-10SC-2.7 | 功能描述:電可擦除可編程只讀存儲器 8K (1Kx8) 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080N-10SE-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| AT25080N-10SI | 功能描述:電可擦除可編程只讀存儲器 RO 511-M95080-WMN6 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080N-10SI-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25080N-10SI-2.7 | 制造商:Atmel Corporation 功能描述:Serial EEPROM, 1K x 8, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。