- 您現在的位置：買賣IC網 > PDF目錄295111 > AT25080N-10SC-1.8 (ATMEL CORP) SPI Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT25080N-10SC-1.8 |
| 廠商： | ATMEL CORP |
| 元件分類： | PROM |
| 英文描述： | SPI Serial EEPROMs |
| 中文描述： | 1K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOIC-8 |
| 文件頁數： | 18/19頁 |
| 文件大?。?/td> | 279K |
| 代理商： | AT25080N-10SC-1.8 |
8
AT25080/160/320/640
0675F–08/01
Functional
Description
The AT25080/160/320/640 is designed to interface directly with the synchronous serial periph-
eral interface (SPI) of the 6805 and 68HC11 series of microcontrollers.
The AT25080/160/320/640 utilizes an 8-bit instruction register. The list of instructions and their
operation codes are contained in Table 1. All instructions, addresses, and data are transferred
with the MSB first and start with a high-to-low CS transition.
WRITE ENABLE (WREN): The device will power-up in the write disable state when VCC is
applied. All programming instructions must therefore be preceded by a Write Enable
instruction.
WRITE DISABLE (WRDI): To protect the device against inadvertent writes, the Write Disable
instruction disables all programming modes. The WRDI instruction is independent of the sta-
tus of the WP pin.
READ STATUS REGISTER (RDSR): The Read Status Register instruction provides access to
the status register. The READY/BUSY and Write Enable status of the device can be deter-
mined by the RDSR instruction. Similarly, the Block Write Protection bits indicate the extent of
protection employed. These bits are set by using the WRSR instruction.
Table 1. Instruction Set for the AT25080/160/320/640
Instruction Name
Instruction Format
Operation
WREN
0000 X110
Set Write Enable Latch
WRDI
0000 X100
Reset Write Enable Latch
RDSR
0000 X101
Read Status Register
WRSR
0000 X001
Write Status Register
READ
0000 X011
Read Data from Memory Array
WRITE
0000 X010
Write Data to Memory Array
Table 2. Status Register Format
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WPEN
X
BP1
BP0
WEN
RDY
Table 3. Read Status Register Bit Definition
Bit
Definition
Bit 0 (RDY)
Bit 0 = 0 (RDY) indicates the device is READY. Bit 0 = 1 indicates the write cycle is
in progress.
Bit 1 (WEN)
Bit 1= 0 indicates the device is not WRITE ENABLED. Bit 1 = 1 indicates the
device is WRITE ENABLED.
Bit 2 (BP0)
See Table 3.
Bit 3 (BP1)
See Table 3.
Bits 4 - 6 are 0s when device is not in an internal write cycle.
Bit 7 (WPEN)
See Table 7.
Bits 0 - 7 are 1s during an internal write cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| AT25080N-10SI | SPI Serial EEPROMs |
| AT25080-10PI-2.7 | SPI Serial EEPROMs |
| AT25080N-10SI-1.8 | SPI Serial EEPROMs |
| AT25080N-10SI-2.7 | SPI Serial EEPROMs |
| AT25080A-10PI-2.7 | SPI Serial EEPROMs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25080N-10SC-2.7 | 功能描述:電可擦除可編程只讀存儲器 8K (1Kx8) 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080N-10SE-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| AT25080N-10SI | 功能描述:電可擦除可編程只讀存儲器 RO 511-M95080-WMN6 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080N-10SI-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25080N-10SI-2.7 | 制造商:Atmel Corporation 功能描述:Serial EEPROM, 1K x 8, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。