- 您現在的位置：買賣IC網 > PDF目錄67389 > AT42QT1111-AU (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AT42QT1111-AU |
| 廠商： | ATMEL CORP |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, MS-026ABA, TQFP-32 |
| 文件頁數： | 15/50頁 |
| 文件大?。?/td> | 637K |
| 代理商： | AT42QT1111-AU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
22
9571B–AT42–08/10
AT42QT1111-MU/AT42QT1111-AU
5.
Control Commands
5.1
Introduction
The QT1111 control commands are those commands that affect the device operation.
The control commands are listed in Table 5-1 and are described individually in the following
sections.
Note:
Commands are implemented immediately upon reception, so a suitable delay is
required for the operation to be completed before communications can be
re-established.
5.2
Send Setups (0x01)
This command initiates the upload of the full settings table to the QT1111 (see Section 7 on
When this command is received, the QT1111 stops key measurement and waits until 42 bytes of
setup data have been received. Key acquisition will restart after all the setup data has been
received.
If enabled, a CRC check byte is transmitted (both ways) after the 42 bytes to confirm that they
have been received correctly.
If CRC checking is not enabled, it is recommended that the host request a dump of setup data
from the QT1111, and confirms that the data correctly matches the data sent.
The host must wait for at least 300 s for the operation to be completed before communications
can be re-established.
5.3
Calibrate All (0x03)
This command initiates the recalibration of all sensor keys.
The host must wait for at least 300 s for the operation to be completed before communications
can be re-established.
Table 5-1.
Control Commands
Command
Code
Note
Send Setups
0x01
Configures the device to receive setup data
Calibrate All
0x03
Calibrates all keys
Reset
0x04
Resets the device
Sleep
0x05
Sleep (dead) mode
Store to EEPROM
0x0A
Stores RAM setups to EEPROM
Restore from EEPROM
0x0B
Copies EEPROM setups to RAM (automatically done at
startup)
Erase EEPROM
0x0C
Erases EEPROM setups
Recover EEPROM
0x0D
Restores last EEPROM settings (after erase)
Calibrate Key 'k'
0x1k
Calibrates one key (key k)
相關PDF資料 |
PDF描述 |
|---|---|
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-TR1 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-50189 | 0 MHz - 2400 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1111-AU QS383 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1111MU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC |
| AT42QT1111-MU | 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1111-MU QS384 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1244-AU | 功能描述:電容觸摸傳感器 QMatrix FMEA 24 Key Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。