參數資料
| 型號： | AT89C51ID2-SLRIM |
| 廠商： | Atmel |
| 文件頁數： | 6/157頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU FLASH 8051 64K 5V 44-PLCC |
| 標準包裝： | 1 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 60MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 2K x 8 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 包裝： | 剪切帶 (CT) |
| 其它名稱： | AT89C51ID2SLRIMCT |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
103
AT89C51ID2
4289C–8051–11/05
Error Conditions
The following flags in the SPSTA signal SPI error conditions:
Mode Fault (MODF)
Mode Fault error in Master mode SPI indicates that the level on the Slave Select (SS)
pin is inconsistent with the actual mode of the device. MODF is set to warn that there
may be a multi-master conflict for system control. In this case, the SPI system is
affected in the following ways:
An SPI receiver/error CPU interrupt request is generated
The SPEN bit in SPCON is cleared. This disables the SPI
The MSTR bit in SPCON is cleared
When SS Disable (SSDIS) bit in the SPCON register is cleared, the MODF flag is set
when the SS signal becomes ’0’.
However, as stated before, for a system with one Master, if the SS pin of the Master
device is pulled low, there is no way that another Master attempts to drive the network.
In this case, to prevent the MODF flag from being set, software can set the SSDIS bit in
the SPCON register and therefore making the SS pin as a general-purpose I/O pin.
Clearing the MODF bit is accomplished by a read of SPSTA register with MODF bit set,
followed by a write to the SPCON register. SPEN Control bit may be restored to its orig-
inal set state after the MODF bit has been cleared.
Write Collision (WCOL)
A Write Collision (WCOL) flag in the SPSTA is set when a write to the SPDAT register is
done during a transmit sequence.
WCOL does not cause an interruption, and the transfer continues uninterrupted.
Clearing the WCOL bit is done through a software sequence of an access to SPSTA
and an access to SPDAT.
Overrun Condition
An overrun condition occurs when the Master device tries to send several data Bytes
and the Slave devise has not cleared the SPIF bit issuing from the previous data Byte
transmitted. In this case, the receiver buffer contains the Byte sent after the SPIF bit was
last cleared. A read of the SPDAT returns this Byte. All others Bytes are lost.
This condition is not detected by the SPI peripheral.
SS Error Flag (SSERR)
A Synchronous Serial Slave Error occurs when SS goes high before the end of a
received data in slave mode. SSERR does not cause in interruption, this bit is cleared
by writing 0 to SPEN bit (reset of the SPI state machine).
Interrupts
Two SPI status flags can generate a CPU interrupt requests:
Table 78. SPI Interrupts
Serial Peripheral data transfer flag, SPIF: This bit is set by hardware when a transfer
has been completed. SPIF bit generates transmitter CPU interrupt requests.
Mode Fault flag, MODF: This bit becomes set to indicate that the level on the SS is
inconsistent with the mode of the SPI. MODF with SSDIS reset, generates receiver/error
CPU interrupt requests. When SSDIS is set, no MODF interrupt request is generated.
Figure 42 gives a logical view of the above statements.
Flag
Request
SPIF (SP data transfer)
SPI Transmitter Interrupt request
MODF (Mode Fault)
SPI Receiver/Error Interrupt Request (if SSDIS = ’0’)
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C923-04/L | IC MCU OTP 4KX14 LCD DVR 68PLCC |
| PIC18F2423-I/SO | IC PIC MCU FLASH 8KX16 28SOIC |
| PIC16C57-LP/SO | IC MCU OTP 2KX12 28SOIC |
| PIC18LF6410-I/PT | IC PIC MCU FLASH 8KX16 64TQFP |
| AT89C51IC2-SLRIM | IC MCU FLASH 8051 32K 5V 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT89C51ID2-SLRUM | 功能描述:8位微控制器 -MCU C51ID2 64K FLASH TWI 32KHz 5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT89C51ID2-SLSIM | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller |
| AT89C51ID2-SLSUM | 功能描述:8位微控制器 -MCU 64K FLASH 32KHz 3.5-5V Ind. RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT89C51ID2-SMSIM | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller |
| AT89C51ID2-UM | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。