參數資料
型號: ATTINY2313A-SUR
廠商: Atmel
文件頁數: 93/172頁
文件大?。?/td> 0K
描述: MCU AVR 2KB FLASH 20MHZ 20SOIC
產品培訓模塊: tinyAVR Introduction
標準包裝: 1,000
系列: AVR® ATtiny
核心處理器: AVR
芯體尺寸: 8-位
速度: 20MHz
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 18
程序存儲器容量: 2KB(1K x 16)
程序存儲器類型: 閃存
EEPROM 大小: 128 x 8
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 1.8 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
包裝: 帶卷 (TR)
其它名稱: ATTINY2313A-SUR-ND
27
8246B–AVR–09/11
ATtiny2313A/4313
6.2
Clock Sources
The device has the following clock source options, selectable by Flash Fuse bits as shown
below. The clock from the selected source is input to the AVR clock generator, and routed to the
appropriate modules.
Note:
1. For all fuses “1” means unprogrammed while “0” means programmed.
The various choices for each clocking option is given in the following sections. When the CPU
wakes up from Power-down, the selected clock source is used to time the start-up, ensuring sta-
ble Oscillator operation before instruction execution starts. When the CPU starts from reset,
there is an additional delay allowing the power to reach a stable level before commencing nor-
mal operation. The Watchdog Oscillator is used for timing this real-time part of the start-up time.
6.2.1
Default Clock Source
The device is shipped with CKSEL = “0100”, SUT = “10”, and CKDIV8 programmed. The default
clock source setting is the Internal RC Oscillator with longest start-up time and an initial system
clock prescaling of 8, resulting in 1.0 MHz system clock. This default setting ensures that all
users can make their desired clock source setting using an In-System or Parallel programmer.
For low-voltage devices it should be noted that unprogramming the CKDIV8 fuse may result in
overclocking. At low voltages (below 2.7V) the devices are rated for maximum 4 MHz operation
(see Section 22.3 on page 200), but routing the clock signal from the internal oscillator directly to
the system clock line will run the device at 8 MHz.
6.2.2
External Clock
To drive the device from an external clock source, XTAL1 should be driven as shown in Figure
6-2. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Table 6-1.
Device Clocking Select
Device Clocking Option
CKSEL3..0(1)
External Clock (see page 27)
0000
Calibrated Internal RC Oscillator 4 MHz (see page 28)
0010
Calibrated internal RC Oscillator 8 MHz (see page 28)
0100
128 kHz Internal Oscillator (see page 29)
0110
External Crystal/Ceramic Resonator (see page 30)
1000 - 1111
Reserved
0001/0011/0101/0111
相關PDF資料
PDF描述
ATTINY24A-MFR MCU AVR 2KB FLASH 20MHZ 20QFN
PCA9575PW2,118 IC I2C/SMBUS 16BIT GPIO 28TSSOP
ATTINY44A-SSUR MCU AVR 4KB FLASH 20MHZ 14SOIC
PCA8575D,112 IC I/O EXPANDER I2C 16B 24SOIC
PCA9535CPW,118 IC I/O EXPANDER I2C 16B 24TSSOP
相關代理商/技術參數
參數描述
ATTINY2313V 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY2313V_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATtiny2313V-10MI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATtiny2313V-10MU 功能描述:8位微控制器 -MCU 2kB Flash 0.128kB EEPROM 18 I/O Pins RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY2313V-10MUR 功能描述:8位微控制器 -MCU AVR 2KFL 128B EE1.8V 128B 1UART 20P-10MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT