- 您現在的位置：買賣IC網 > PDF目錄295139 > BD00HA5WEFJ ADJUSTABLE POSITIVE LDO REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | BD00HA5WEFJ |
| 元件分類： | 可調正電壓單路輸出LDO穩壓器 |
| 英文描述： | ADJUSTABLE POSITIVE LDO REGULATOR, PDSO8 |
| 封裝： | ROHS COMPLIANT, HTSOP-8 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 416K |
| 代理商： | BD00HA5WEFJ |
www.rohm.com
2010.10 - Rev.A
2010 ROHM Co., Ltd. All rights reserved.
Technical Note
6/11
BD00IA5WEFJ
Stable area characteristics
(Characteristics example)
●
Heat Loss
Thermal design should allow operation within the following conditions. Note that the temperatures listed are the allowed
temperature limits, and thermal design should allow sufficient margin from the limits.
1. Ambient temperature Ta can be no higher than 85℃.
2. Chip junction temperature (Tj) can be no higher than 150℃.
Chip junction temperature can be determined as follows:
①
Calculation based on ambient temperature (Ta)
Tj=Ta+θj-a×W
＜
Reference values＞
θ
j-a：HTSOP-J8 153.2℃/W
113.6℃/W
59.2℃/W
33.3℃/W
1-layer substrate (copper foil density 0mm×0mm)
2-layer substrate (copper foil density 15mm×15mm)
2-layer substrate (copper foil density 70mm×70mm)
4-layer substrate (copper foil density 70mm×70mm)
Substrate size: 70×70×1.6mm
3 (substrate with thermal via)
Most of the heat loss that occurs in the BD00IA5WEFJ is generated from the output Pch FET. Power loss is determined by
the total Vcc-Vo voltage and output current. Be sure to confirm the system input and output voltage and the output current
conditions in relation to the heat dissipation characteristics of the VIN and Vo in the design. Bearing in mind that heat
dissipation may vary substantially depending on the substrate employed (due to the power package incorporated in the
BD00IA5WEFJ make certain to factor conditions such as substrate size into the thermal design.
Power consumption (W) = Input voltage (VCC)- Output voltage (Vo)
×
Io(Ave)
Example) Where VCC=3.3V, VO=2.5V, Io(Ave) = 0.1A,
Power consumption (W) = 3.3(V)-2.5(V) ×0.1(A)
=0.08(W)
●
About equivalent series resistance ESR (ceramic capacitor etc.)
Capacitor usually has ESR(Equivalent Series Resistance), and
operates stable in ESR-OUT range, showed right. Generally, ESR of
ceramic, tantalum and electronic capacitor etc. is different for each,
so please be sure to check a capacitor which is going to use, and
use it inside the stable range, showed right. Then, please evaluate
for the actual application
0.01
0.1
1
10
100
0
50
100
150
200
IOUT [mA]
ESR
[
]
Capacity-Bias characteristics
相關PDF資料 |
PDF描述 |
|---|---|
| BD45485G | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| BD4837FVE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| BD538 | Complemetary Silicon Power Transistors(互補硅功率晶體管) |
| BD6637KV-E2 | DISK DRIVE MOTOR CONTROLLER, 1 A, PQFP64 |
| BD792 | 4 A, 100 V, PNP, Si, POWER TRANSISTOR, TO-225AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD00HA5WEFJ_13 | 制造商:ROHM 制造商全稱:Rohm 功能描述:500mA Variable Fixed Output LDO Regulators |
| BD00HA5WEFJ-E2 | 功能描述:低壓差穩壓器 - LDO LDO REG 0.8V-7V 0.5A 8PIN RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BD00HA5WEFJ-ME2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Automotive 0.5A Variable Output LDO Regulator |
| BD00HC0EFJ-E2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:500mA Secondary Variable Output LDO Regulators for Local Power Supplies |
| BD00HC0MEFJ-M | 制造商:ROHM 制造商全稱:Rohm 功能描述:Automotive 1.0A Variable Output LDO Regulator |
發布緊急采購，3分鐘左右您將得到回復。