參數資料
型號： BD792
廠商： ON SEMICONDUCTOR
元件分類： 功率晶體管
英文描述： 4 A, 100 V, PNP, Si, POWER TRANSISTOR, TO-225AA
封裝： PLASTIC, FORMERLY TO-126, 3 PIN
文件頁數： 13/61頁
文件大?。?/td> 372K
代理商： BD792
4–3
Surface Mount Package Information and Tape and Reel Specifications
Motorola Bipolar Power Transistor Device Data
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads.
Solder stencils are used to screen the optimum amount.
These stencils are typically 0.008 inches thick and may be
made of brass or stainless steel. This is not the case with the
DPAK and D2PAK packages. If a 1:1 opening is used to
screen solder onto the drain pad, misalignment and/or “tomb-
stoning” may occur due to an excess of solder. For these two
packages, the opening in the stencil for the paste should be
approximately 50% of the tab area. The opening for the leads
is still a 1:1 registration. Figure 3 shows a typical stencil for
the DPAK and D2PAK packages. The pattern of the opening
in the stencil for the drain pad is not critical as long as it
allows approximately 50% of the pad to be covered with
paste.
Figure 3. Typical Stencil for DPAK and
D2PAK Packages
SOLDER PASTE
OPENINGS
STENCIL
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to mini-
mize the thermal stress to which the devices are subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10
°C.
The soldering temperature and time should not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used since the use of forced
cooling will increase the temperature gradient and will
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
* Due to shadowing and the inability to set the wave height to
incorporate other surface mount components, the D2PAK is
not recommended for wave soldering.
相關PDF資料
PDF描述
BD9403KV SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO14
BD9781HFP-TR 4 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PSSO7
BDE0300G ANALOG TEMP SENSOR-VOLTAGE, 1.716-1.79V, 3.5Cel, RECTANGULAR, SURFACE MOUNT
BDE9100G ANALOG TEMP SENSOR-VOLTAGE, 1.716-1.79V, 3.5Cel, RECTANGULAR, SURFACE MOUNT
BDE0100G-TR ANALOG TEMP SENSOR-VOLTAGE, 1.716-1.79V, 3.5Cel, RECTANGULAR, SURFACE MOUNT
相關代理商/技術參數
參數描述
BD7931F 制造商:ROHM 制造商全稱:Rohm 功能描述:Reversible Motor Drivers for Output 0.5A 1 Motor
BD7931FE2 制造商:ROHM Semiconductor 功能描述:
BD7931F-E2 功能描述:馬達/運動/點火控制器和驅動器 REVERSIBLE 0.5A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
BD7931F-TR 制造商:ROHM 制造商全稱:Rohm 功能描述:0.5A or Less Reversible Motor Drivers (Single Moter)
BD795 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:EPITAXIAL-BASE,SILICON N-P-N AND P-N-P VERSAWATT TRANSISTORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*