- 您現在的位置：買賣IC網 > PDF目錄295161 > BQ25070DQCR (TEXAS INSTRUMENTS INC) 1 A BATTERY CHARGE CONTROLLER, PDSO10 PDF資料下載
參數資料
| 型號： | BQ25070DQCR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1 A BATTERY CHARGE CONTROLLER, PDSO10 |
| 封裝： | 2 X 3 MM, GREEN, PLASTIC, SON-10 |
| 文件頁數： | 4/21頁 |
| 文件大?。?/td> | 664K |
| 代理商： | BQ25070DQCR |
bq25070
TS
TEMP
PACK+
PACK -
+
V
HOT
V
COLD
R2
R1
LDO
SLUSA66
– JULY 2011
For applications that do not require the TS monitoring function, set R1 = 490k
Ω and R2 = 100kΩ to set the TS voltage
at a valid level and maintain charging.
Figure 14. NTC Monitoring Function
50 mA LDO (LDO)
The LDO output of the bq25070 is a low dropout linear regulator (LDO) that supplies up to 50mA while regulating
to VLDO. The LDO is active whenever the input voltage is above VUVLO and below VOVP. It is not affected by the
CTRL input. The LDO output is used to power and protect circuitry such as USB transceivers from transients on
the input supply.
CHARGE STATUS INDICATOR (CHG)
The bq25070 contains an open drain CHG output that indicates when charge cycles and faults. When charging a
battery in precharge or fastcharge mode, the CHG output is pulled to GND. Once the BAT output reaches the
overcharge voltage threshold, CHG goes high impedance to signal the battery is fully charged. The CHG output
goes low during battery recharge cycles to signal the host.
Additionally, CHG notifies the host if a NTC temperature fault has occurred. CHG pulses with a period of 100ms
and a 50% duty cycle if a TS faults occurs. Connect CHG to the required logic level voltage through a 1k
Ω to
100k
Ω resistor to use the signal with a microprocessor. ICHG must be below 5mA.
The IC monitors the CHG pin when no input is connected to verify if the system circuitry is active. If the voltage
at CHG is logic being drive low when no input is connected, the TS circuit is turned off for a low quiescent current
state. Once the voltage at CHG increases above logic high, the TS circuit is turned on.
SINGLE INPUT INTERFACE (CTRL)
CTRL is used to enable/disable the device as well as select the input current limit, enable/disable charge, extend
the TS operation range and disable VIN-DPM mode. CTRL is pulled low to enable the device. After the 50μs
deglitch expires, the IC enters the 32ms WAIT state. CTRL may be used to program the bq25070 during this
time. Once tWAIT expires, the IC starts up. If no command is sent to CTRL during tWAIT, the IC starts up with a
default 285mA current limit.
Programming the different modes is done by pulsing the CTRL input. See Table 1 for a map of the different
modes. The width of the CTRL pulses is unimportant as long as they are between 50
μs and 1000μs long. The
time between pulses must be between 50
μs and 1000μs to be properly read. Once CTRL is held low for 2ms,
the number of pulses is passed to the control logic and decoded and then the mode changes. To ensure proper
operation, do not send more than 16 pulses in one programming cycle.
12
Copyright
2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| BQ3285ESSNTR | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285ESS-N | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285ESSN | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285LCSS | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285ECSS | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ25070DQCT | 功能描述:電池管理 1A,Sgl cell,Linear Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ25070EVM-740 | 功能描述:電源管理IC開發工具 BQ25070 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ25071DQCR | 功能描述:IC LINEAR BATT CHRGR SGL 10WSON 制造商:texas instruments 系列:- 包裝:帶卷（TR） 零件狀態:有效 電池化學:磷酸鐵鋰 電池數:1 電流 - 充電:恒流 - 可編程 可編程特性:- 故障保護:超溫，過壓 充電電流 - 最大值:1A 電池組電壓:3.5V 電壓 -?供電（最高）:10.2V 接口:USB 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:10-WFDFN 裸露焊盤 供應商器件封裝:10-WSON（3x2） 標準包裝:3,000 |
| BQ25071DQCT | 功能描述:IC LINEAR BATT CHRGR SGL 10WSON 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 電池化學:磷酸鐵鋰 電池數:1 Current Charging:恒流 - 可編程 可編程特性:- 故障保護:超溫，過壓 充電電流 - 最大值:1A Battery Pack Voltage:3.5V 電壓 -?供電（最高）:10.2V 接口:USB 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:10-WFDFN 裸露焊盤 供應商器件封裝:10-WSON（3x2） 標準包裝:1 |
| BQ25071EVM-658 | 功能描述:BQ25071 - Power Management, Battery Charger Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 主要用途:電源管理，電池充電器 嵌入式:- 使用的 IC/零件:BQ25071 主要屬性:- 輔助屬性:LED 狀態指示器 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。