參數資料
型號： BU-61703F4-112
廠商： DATA DEVICE CORP
元件分類： 微控制器/微處理器
英文描述： 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
封裝： 1 X 1 INCH, 0.155 INCH HEIGHT, CERAMIC, FP-72
文件頁數： 30/52頁
文件大?。?/td> 367K
代理商： BU-61703F4-112
36
BIT WORD
The BU-61703/5 provides an internally formulated Built-In-Test
word (BIT word). This word is transmitted to the BC in response
to a Transmit BIT Word Mode Code Command. The BIT word bit
functions and descriptions are provided in Table 5.
If set, indicates that, for the previous message, the SSRT was the receiving RT for an RT-to-RT trans-
fer and that the transmitting RT either did not respond or responded later than the SSRT RT-to-RT
timeout time. The SSRT's RT-to-RT response timeout time is defined as the time from the mid-bit
crossing of the parity bit of the transmit Command Word to the mid-sync crossing of the transmitting
RT status word. The value of the SSRT's RT-to-RT response timeout time is in the range from 17.5 to
19.5 s.
Indicates that a received command word is not defined in accordance with MIL-STD-1553B. This
includes the following undefined Command Words: (1) The Command Word is a non-mode code,
broadcast, transmit command; (2) a message with a T/R bit of "0", a subaddress/mode field of 00000
or 11111, and a mode code field with a value between 00000 and 01111; (3) a mode code command
that is not permitted to be broadcast (e.g., Transmit Status) is sent to the broadcast address 11111.
Indicates that the SSRT received one or more words containing one or more of the following error
types: sync field error, Manchester encoding error, parity error, and/or bit count error.
This bit is set if the SSRT is the receiving RT for an RT-to-RT transfer and one or more of the following
errors occurs: (1) If the transmitting RT responds with a response time of less than 4 s, per MIL-
STD-1553B (mid-parity bit to mid-sync); i.e., less than 2 s dead time; and/or (2) There is an incorrect
sync type or format error (encoding, bit count, and/or parity error) in the transmitting RT Status Word;
and/or (3) The RT address field of the transmitting RT Status Word does not match the RT address in
the transmit Command Word.
If the SSRT is the receiving RT for an RT-to-RT transfer, if this bit is set, it indicates one or more of the
following error conditions in the transmit Command Word: (1) T/R bit = logic "0"; (2) subaddress =
00000 or 11111; (3) same RT Address field as the receive Command Word.
If set, indicates that the SSRT detected a Command sync in a received Data Word.
Set to logic "1" if the previous message had a low word count error.
RT-RT TRANSFER
NO RESPONSE
TIMEOUT
COMMAND WORD
CONTENTS ERROR
INVALID WORD
MANCHESTER/PARITY ERROR
RECEIVED
RT-RT TRANSFER RESPONSE
ERROR (no gap, data, sync,
address mismatch)
RT-RT TRANSFER -
T/R ERROR ON
SECOND COMMAND
OR
INVALID ADDRESS
INCORRECT SYNC TYPE
RECEIVED
LOW WORD COUNT
2
0 (LSB)
4
3
1
5
6
Set to logic "1" if the previous message had a high word count error.
HIGH WORD COUNT
7
Set to logic "1" to denote that the SSRT has failed its off-line protocol self-test. This bit will be logic "0"
if the self-test passed or had not been performed.
BIT TEST FAIL
8
Set to logic "1" if the SSRT's Terminal flag RT status bit has been disabled by an Inhibit terminal flag
mode code command. Will revert to logic "0" if an Override inhibit terminal flag mode code command
is received.
TERMINAL FLAG INHIBITED
9
If this bit is set, it indicates that the subsystem had failed to respond with the DMA handshake input
DTGRT* asserted within 10 s after the SSRT has asserted DTREQ*.
HANDSHAKE FAILURE
12
A loopback test is performed on the transmitted portion of every non-broadcast message. A validity
check is performed on the received version of every word transmitted by the SSRT. In addition, a bit-
by-bit comparison is performed on the last word transmitted by the RT for each message. If either the
received version of the last word does not match the transmitted version and/or the received version
of any transmitted word is determined to be invalid (sync, encoding, bit count, parity), or a failsafe
timeout occurs on the respective channel, the LOOP TEST FAILURE bit for the respective bus chan-
nel will be set.
CH. B LOOP TEST FAILURE
CH. A LOOP TEST FAILURE
14
13
Set if the SSRT's failsafe timer detected a fault condition. The transmitter timeout circuit will automati-
cally shut down the CH. A or CH. B transmitter if it transmits for longer than 660.5 s.
TRANSMITTER TIMEOUT
15 (MSB)
TABLE 5. INTERNAL BUILT-IN-TEST (BIT) WORD DEFINITION
DESCRIPTION
FUNCTION
BIT
If either of these bits are logic "1", this indicates that the respective 1553 transmitter has been shut
down by means of a Transmitter shutdown mode command.
TRANSMITTER SHUTDOWN B
TRANSMITTER SHUTDOWN A
11
10
Note:
Bits 15 through 9 are cleared only following a RESET input or receipt of a Reset Remote Terminal mode command. Bits 8 through 0 are updated
as a result of every message processed.
相關PDF資料
PDF描述
BU-61703F4-122Q 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
BU-61703F4-132S 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
BU-61703F4-132Z 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
BU-61703F4-142L 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
BU-61703F4-142Z 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP72
相關代理商/技術參數
參數描述
BU-61705 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |Simple System RT
BU-61740B3NEW 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |μ-ACE (Micro-ACE?)
BU-61743 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |Enhanced Mini-ACE?
BU-61743F3-100 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
BU-61743F3-110 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*