參數資料
型號: DAC8544I
廠商: Texas Instruments, Inc.
英文描述: QUAD, 16-BIT, RAIL-TO-RAIL VOLTAGE OUTPUT, PARALLEL INTERFACE, DIGITAL-TO-ANALOG CONVERTER
中文描述: 四,16位,軌到軌電壓輸出,并行接口,數字模擬轉換器
文件頁數: 18/20頁
文件大?。?/td> 476K
代理商: DAC8544I
www.ti.com
LAYOUT
A precision analog component requires careful layout, adequate bypassing, and clean, well-regulated power
supplies. The following measures should be taken to assure optimum performance of the DAC8544. The
DAC8544 offers dual-supply operation, as it can often be used in close proximity with digital logic,
microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and
the higher the switching speed, the more important it becomes to separate the analog and digital ground and
supply planes at the DAC.
DAC8544
SLAS420–MAY 2004
Because the DAC8544 has both analog and digital ground pins, return currents can be better controlled and
have less effect on the DAC output error. Ideally, GND would be connected directly to an analog ground plane
and GND to the digital ground plane. The analog ground plane would be separate from the ground connection for
the digital components until they were connected at the power entry point of the system. The power applied to
V
DD
and V
REF+
(this also applies to V
REF–
if not tied to GND) should be well-regulated and low-noise. Switching
power supplies and dc/dc converters often have high-frequency glitches or spikes riding on the output voltage. In
addition, digital components can create similar high-frequency spikes as their internal logic switches states. This
noise can easily couple into the DAC output voltage through various paths between the power connections and
analog output.
As with the GND connection, V
DD
should be connected to a 5-V power supply plane or trace that is separate
from the connection for digital logic until they are connected at the power entry point. In addition, the 1-μF to
10-μF and 0.1-μF bypass capacitors are strongly recommended. In some situations, additional bypassing may be
required, such as a 100-μF electrolytic capacitor or even a Pi filter made up of inductors and capacitors—all
designed to essentially lowpass-filter the V
DD
supply, removing the high-frequency noise.
18
相關PDF資料
PDF描述
DAC8551IDGK 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER
DAC8551IDRBR 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER
DAC8551IDRBT 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER
DAC8562ER 12-Bit Digital-to-Analog Converter
DAC8512EZ 12-Bit Digital-to-Analog Converter
相關代理商/技術參數
參數描述
DAC8544IPFB 功能描述:數模轉換器- DAC Quad 16-Bit R-to-R Vltg Out Paral Intfc RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC8544IPFBG4 功能描述:數模轉換器- DAC Quad 16-Bit R-to-R Vltg Out Paral Intfc RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC8544IPFBR 功能描述:數模轉換器- DAC Quad 16-Bit R-to-R Vltg Out Paral Intfc RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC8544IPFBRG4 功能描述:數模轉換器- DAC Quad 16-Bit R-to-R Vltg Out Paral Intfc RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
DAC8550 制造商:BB 制造商全稱:BB 功能描述:16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER