- 您現在的位置：買賣IC網 > PDF目錄17069 > DC1067A-A (Linear Technology)BOARD DELTA SIGMA ADC LTC2450 PDF資料下載
參數資料
| 型號： | DC1067A-A |
| 廠商： | Linear Technology |
| 文件頁數： | 6/20頁 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2450 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC1067A Design File DC1067A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 30 |
| 數據接口： | 串行，SPI? |
| 已用 IC / 零件： | LTC2450 |
| 已供物品： | 板 |
| 相關產品： | LTC2450IDC#TRPBF-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450IDC-1#TRPBF-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450IDC-1#TRMPBFTR-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450IDC#TRMPBFTR-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450CDC-1#TRPBF-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450CDC-1#TRMPBFTR-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450CDC#TRPBF-ND - IC ADC 16BIT DELTA SIG 6-DFN LTC2450CDC#TRMPBFTR-ND - IC ADC 16BIT DELTA SIG 6-DFN |
LTC2450
14
2450fb
APPLICATIONS INFORMATION
Digital Signal Levels
The LTC2450’s digital interface is easy to use. Its digital
inputs (SCK and CS) accept standard CMOS logic levels
and the internal hysteresis receivers can tolerate edge
rates as slow as 100μs. However, some considerations
are required to take advantage of the exceptional accuracy
and low supply current of this converter.
The digital output signal SDO is less of a concern because
it is not active during the conversion cycle.
While a digital input signal is in the range 0.5V to VCC
–0.5V, the CMOS input receiver may draw additional
current from the power supply. Due to the nature of CMOS
logic, a slow transition within this voltage range may cause
an increase in the power supply current drawn by the
converter, particularly in the low power operation mode
within the SLEEP state. Thus, for low power consumption
it is highly desirable to provide relatively fast edges for the
two digital input pins SCK and CS, and to keep the digital
input logic levels at VCC or GND.
At the same time, during the CONVERT state, undershoot
and/or overshoot of fast digital signals connected to the
LTC2450 pins may alter the conversion result. Under-
shoot and overshoot can occur because of an impedance
mismatch at the converter pin combined with very fast
transition times. This problem becomes particularly difcult
when shared control lines are used and multiple reec-
tions may occur. The solution is to carefully terminate all
transmission lines close to their characteristic impedance.
Parallel termination is seldom an acceptable option in low
power systems so a series resistor between 27Ω and 56Ω
placed near the driver may eliminate this problem. The
actual resistor value depends upon the trace impedance
and connection topology. An alternate solution is to reduce
the edge rate of the control signals, keeping in mind the
concerns regarding slow edges mentioned above.
Particular attention should be given to congurations in
which a continuous clock signal is applied to SCK pin during
the CONVERT state. While LTC2450 will ignore this signal
from a logic point of view the signal edges may create
unexpected errors depending upon the relation between
its frequency and the internal oscillator frequency. In such
a situation it is benecial to use edge rates of about 10ns
and to limit potential undershoot to less than 0.3V below
GND and overshoot to less than 0.3V above VCC.
Noisy external circuitry can potentially impact the output
under 2-wire operation. In particular, it is possible to get
the LTC2450 into an unknown state if an SCK pulse is
missed or noise triggers an extra SCK pulse. In this situ-
ation, it is impossible to distinguish SDO = 1 (indicating
conversion in progress) from valid “1” data bits. As such,
CPOL = 1 is recommended for the 2-wire mode. The user
should look for SDO = 0 before reading data, and look
for SDO = 1 after reading data. If SDO does not return a
“0” within the maximum conversion time (or return a “1”
after a full data read), generate 16 SCK pulses to force a
new conversion.
Driving VCC and GND
The VCC and GND pins of the LTC2450 converter are
directly connected to the positive and negative reference
voltages, respectively. A simplied equivalent circuit is
shown in Figure 14.
The power supply current passing through the parasitic
layout resistance associated with these common pins will
modify the ADC reference voltage and thus negatively affect
the converter accuracy. It is thus important to keep the
VCC and GND lines quiet, and to connect these supplies
through very low impedance traces.
In relation to the VCC and GND pins, the LTC2450 com-
bines internal high frequency decoupling with damping
Figure 14. LTC2450 Analog Pins Equivalent Circuit
VCC
ILEAK
RSW (TYP)
15k
CEQ (TYP)
0.35pF
INTERNAL SWITCHING FREQUENCY = 4 MHz
RSW (TYP)
15k
RSW (TYP)
15k
VIN
ILEAK
GND
ILEAK
VCC
2450 F14
相關PDF資料 |
PDF描述 |
|---|---|
| 0210390933 | CABLE JUMPER 1MM .178M 23POS |
| PCMC135T-2R2MF | COIL 2.2 UH POWER CHOKE 20% SMD |
| AT-S-26-6/6/B-25-OE-R | MOD CORD SGL-ENDED 6-6 BLACK 25' |
| MIC2005-0.5LYM5 TR | IC DISTRIBUTION SW 0.5A SOT23-5 |
| GSM10DSEI | CONN EDGECARD 20POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1067A-B | 功能描述:BOARD DELTA SIGMA ADC LTC2450-1 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC106R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DC107 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DC1073A | 制造商:Linear Technology 功能描述:LT3845EFE DEMO BOARD |
| DC1074A | 功能描述:BOARD DAC LTC2630-12 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:QuikEval™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。