- 您現在的位置：買賣IC網 > PDF目錄376597 > DDC118IRTCR Octal Current Input 20-Bit Analog-To-Digital Converter PDF資料下載
參數資料
| 型號： | DDC118IRTCR |
| 英文描述： | Octal Current Input 20-Bit Analog-To-Digital Converter |
| 中文描述： | 八路電流輸入20位模擬數字轉換器 |
| 文件頁數： | 20/30頁 |
| 文件大小： | 384K |
| 代理商： | DDC118IRTCR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
""#
SBAS325A JUNE 2004 REVISED JUNE 2005
www.ti.com
20
Changing Between Modes
Changing from the cont to ncont mode occurs whenever
T
INT
< t
6
. Figure 18 shows an example of this transition.
In this figure, the cont mode is entered when the integration
on side A is completed before the m/r/az cycle on side B
is complete. The DDC118 completes the measurement on
sides B and A during states 8 and 7 with the input signal
shorted to ground. Ncont integration begins with state 6.
Changing from the ncont to cont mode occurs when T
INT
is increased so that T
INT
is always
≥
t
6
, as shown in
Figure 19 (see also Figure 14 and Table 8, page 18). With
a longer T
INT
, the m/r/az cycle has enough time to finish
before the next integration begins and continuous
integration of the input signal is possible. For the special
case of the very first integration when changing to the cont
mode, T
INT
can be < t
6
. This is allowed because there is
no simultaneous
m/r/az cycle on the side B during state
3—there is no need to wait for it to finish before ending the
integration on side A.
CONV
8
7
4
5
Continuous
NonContinuous
5
6
5
State
Integration
Status
m/r/az
Status
mbsy
m/r/az B
m/r/az A
m/r/az B
m/r/az A
m/r/az B
Integrate A
Integrate B
Int A
Int A
Int B
Figure 18. Changing from Continuous Mode to Non-Continuous Mode
CONV
4
2
1
4
NonContinuous
Continuous
3
3
State
mbsy
m/r/az
Status
Integration
Status
m/r/az A
m/r/az B
m/r/az A
Int B
Int A
Integrate A
Integrate B
Figure 19. Changing from Non-Continuous Mode to Continuous Mode
相關PDF資料 |
PDF描述 |
|---|---|
| DDC118IRTCT | Octal Current Input 20-Bit Analog-To-Digital Converter |
| DDG-GJS-K1 | LED GaP |
| DDR-GJS-J2L1-1-I1 | LED GaP |
| DDR-GJS-K1 | LED GaP |
| DDR-GJS-K2 | LED GaP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DDC118IRTCRG4 | 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DDC118IRTCT | 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DDC118IRTCT | 制造商:Texas Instruments 功能描述:IC ADC 20BIT OCTAL 48-VQFN |
| DDC118IRTCT | 制造商:Texas Instruments 功能描述:A/D CONVERTER (A-D) IC ((NW)) |
| DDC118IRTCTG4 | 功能描述:模數轉換器 - ADC Octal Current-Input 20-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。