- 您現在的位置：買賣IC網 > PDF目錄376805 > DMC73C168 8Bit Single Chip Microcontroller PDF資料下載
參數資料
| 型號： | DMC73C168 |
| 英文描述： | 8Bit Single Chip Microcontroller |
| 中文描述： | 8位單芯片微控制器 |
| 文件頁數： | 35/90頁 |
| 文件大?。?/td> | 742K |
| 代理商： | DMC73C168 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
35
8Bit Single Chip Microcontroller
DMC73C167
The interrupt flag (INTn-mF) is set to 1 by the INTn_m input. The INTnF flag becomes active
when INTnE is 1, then INTn occurs if the interrupt enable bit (I bit) of the status register is
set to 1.
Figure 5-2. External Interrupt Logic (n = 1, 3 or 5 ; m = 0)
To conserve the low power requirement, one low-power mode - the HALT MODE - is provided.
It is invoked by executing an IDLE instruction. An external interrupt will release the device from
the low-power mode depending on whether it is in the HALTmode. When an external interrupt
is first asserted, its level is gated into an interrupt flag. In order for an interrupt signal to be
detected, the pulse duration must be a minimum of five internal clock cycles.
The INTn Enable bit is used separately to individually mask interrupt levels, and must be set 1
for the interrupt to be recognized.
As Previously stated, all interrupt control bits are implemented in the IOCTL0, IOCTL1, IOCTL2,
IOCTL3, and IOCTL4 registers in the peripheral file. I/O instructions may simply read from and
write to each INTn Enable bit. By the INTn input, the interrupt flag is set to 1 at the falling or
rising edge and becomes active when an interrupt is enabled.The interrupt service routine is
executed after the currently executing instruction is completed. Once the interrupt has been
acknowledged by the CPU, the CPU then pushes the contents of the status register and the
program counter (MSB and LSB), respectively, onto the stack and makes zero the status
register (see Section 4.4). The corresponding vector address is loaded into the program
counter, and the interrupt service routine is executed. The external interrupts, INT1, INT3_0,
and INT5_0, have Schmitt-trigger inputs and can be used as zero-cross detectors.
Because the pins can be used as both external interrupt pins and general-purpose I/O pins,
the following points should be noted :
D
Q
Write
Read
Enable Latch
D
Q
Write
Read
Enable Latch
CL
R
S
Q
InmCLR
EXTINTn
(SCHIMITT)
SENSnm
InmFLG
Read
InmENA
INTnE
INTn
Happen
Interrupt Enable
(ST : Status Register)
Read
INTnF
INTn Enable
￡￡á￡￡×￡￡
相關PDF資料 |
PDF描述 |
|---|---|
| DMC80C49 | CMOS SINGLE-COMPONENT 8-BIT MICROCOMPUTER |
| DMCA1CHP | TRANSISTOR | MOSFET | ARRAY | N-CHANNEL | 20V V(BR)DSS | 50MA I(D) | CHIP |
| DMCB1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 30V V(BR)DSS | 50MA I(D) | CHIP |
| DMCB2CHP | TRANSISTOR | MOSFET | N-CHANNEL | 30V V(BR)DSS | 50MA I(D) | CHIP |
| DMCD1CHP | TRANSISTOR | MOSFET | N-CHANNEL | 25V V(BR)DSS | 50MA I(D) | CHIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DMC757 | 制造商:Daniels Manufacturing Corporation (DMC) 功能描述:CONNECTOR |
| DMC-8/16-15 | 制造商:Brady Corporation 功能描述: |
| DMC-8/16-30 | 制造商:Brady Corporation 功能描述: |
| DMC80C49 | 制造商:DAEWOO 制造商全稱:DAEWOO 功能描述:CMOS SINGLE-COMPONENT 8-BIT MICROCOMPUTER |
| DMC904010R | 功能描述:兩極晶體管 - BJT COMP TRANS W/BLT IN RES FLT LD 1.6x1.6mm RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
發布緊急采購，3分鐘左右您將得到回復。