參數資料
型號: DS2149Q+
廠商: Maxim Integrated Products
文件頁數: 32/32頁
文件大?。?/td> 0K
描述: IC LIU T1/J1 5V 28-PLCC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 37
類型: 線路接口裝置(LIU)
規程: T1/J1
電源電壓: 4.75 V ~ 5.25 V
安裝類型: 表面貼裝
封裝/外殼: 28-LCC(J 形引線)
供應商設備封裝: 28-PLCC(11.51x11.51)
包裝: 管件
產品目錄頁面: 1429 (CN2011-ZH PDF)
DS2149
9 of 32
3. INITIALIZATION AND RESET
During power-up, all control registers are cleared, disabling the transmitter outputs. The device requires a
master clock supplied to the MCLK input pin to operate the PLL. This master clock must be independent,
free-running, and jitter free.
A reset initializes the status and state machines for the RCL, AIS, NLOOP, and QRSS blocks. Under
software control, setting the RESET bit (CR2.7) clears all registers. Allow up to 100ms for the receiver to
recover from initialization.
4. REGISTER DEFINITIONS
The DS2149 contains eight registers for configuring the device and reading status. These are accessible
using the serial port. Table 4-A lists the register names and addresses.
Reading or writing to the internal registers requires writing one address/command byte prior to
transferring register data. The first bit written (LSb) of the address/command byte specifies whether the
access is a read (1) or a write (0). The next 6 bits identify the register address.
The last bit (MSb) of the address/command byte is the burst mode bit. When the burst bit is enabled (set
to 1) and a READ operation is performed, addresses 10h through 17h are read sequentially, starting at
address 10h. And when the burst bit is enabled and a WRITE operation is performed, addresses 10h
through 17h are written sequentially, starting at address 10h. Burst operation is stopped once address 17h
is read. All data transfers are initiated by driving the
CS input low. All data transfers are terminated if the
CS input transitions high. Port control logic is disabled and SDO is tri-stated when CS is high.
Table 4-A. Register Map
REGISTER
SYMBOL
ADDRESS
Control Register 1
CR1
B010000
Control Register 2
CR2
B010001
Control Register 3
CR3
B010010
Interrupt Mask Register
IMR
B010011
Transition Status Register
TSR
B010100
Status Register
SR
B010101
Information Register
IR
B010110
Control Register 4
CR4
B010111
Table 4-B. Register Bit Positions
SYMBOL 7 (MSb)
6
5
4
3
2
1
0 (LSb)
CR1
JASEL1
JASEL0
ENCENB
UNIENB
L3
L2
L1
L0
CR2
RESET
PAT1
PAT0
TAIS
ENLOOP
ALB
LLB
RLB
CR3
JA6HZ
TPD
EQZMON20 EQZMON26
JA128
LIRST
TAOZ
IMR
Z16D
JALT
DFMO
B8ZSD
QRSS
AIS
NLOOP
RCL
TSR
Z16D
JALT
DFMO
B8ZSD
QRSS
AIS
NLOOP
RCL
SR
DFMO
QRSS
AIS
NLOOP
RCL
IR
RL3
RL2
RL1
RL0
LUP
LDN
TSCD
LOTC
CR4
RCL2048
XFMR2
XFMR1
Note: Set unused bits to 0 for normal operation.
相關PDF資料
PDF描述
DS2151QN IC TXRX T1 1-CH 5V LP IND 44PLCC
DS2152L+ IC TXRX T1 1CHIP ENHNCD 100-LQFP
DS2153Q-A7+T&R IC TXRX E1 1-CHIP 5V 44-PLCC
DS2154LNA2+ IC TXRX E1 5V 100-LQFP
DS2154L IC TXRX E1 1CHIP 5V ENH 100-LQFP
相關代理商/技術參數
參數描述
DS2149Q/T&R 制造商:Maxim Integrated Products 功能描述:5V T1/E1 LIU T&R COMM - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LINE INTERFACE 5V T1/E1 PLCC
DS2149Q/T&R+ 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel
DS2149Q/T&R 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2149Q+ 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2149Q+T&R 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 5V 28-PLCC