參數資料
型號： DS2149Q+
廠商： Maxim Integrated Products
文件頁數： 9/32頁
文件大?。?/td> 0K
描述： IC LIU T1/J1 5V 28-PLCC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 37
類型： 線路接口裝置（LIU）
規程： T1/J1
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 28-LCC（J 形引線）
供應商設備封裝： 28-PLCC（11.51x11.51）
包裝： 管件
產品目錄頁面： 1429 (CN2011-ZH PDF)
DS2149
17 of 32
9. SOFTWARE MODE
The DS2149 operates in software mode when the MODE1 pin is pulled high. In software mode, a
microprocessor controls the device and reads its status through the serial port, which provides access to
the internal registers. The host processor can completely configure the device as well as get diagnostics
and status reports through the serial port. In NRZ mode, bipolar violation insertions and logic error
insertions are controlled by the BPV and INSLER pins. Similarly, the recovered clock, data, and BPV
detection are available only at output pins. All other mode settings and diagnostic information are
available through the serial port. Figure 9-1 and Figure 9-2 show the serial port data structure. The
registers are accessible through a 16-bit word composed of an 8-bit command and address byte and a
subsequent 8-bit data byte. Software mode allows control of the output timing. The CLKE pin determines
when SDO is valid relative to SCLK and when receive data is valid relative to RCLK.
9.1 Interrupt Handling
In software mode, the DS2149 provides a latched interrupt output pin. When enabled, a change in any of
the status register bits generates an interrupt. When an interrupt occurs, the INT output pin is driven low.
The INT output pin structure is an open-drain only. Each device that shares the INT line requires an
external pullup resistor. The interrupt is cleared when the interrupt condition no longer exists, and a 1 is
written to the appropriate bit in the interrupt mask register. Leaving a 1 in any of the bits in the interrupt
mask register masks that interrupt. Clearing that bit re-enables the interrupt.
Table 9-A. CLKE Pin Selection
CLKE PIN
OUTPUT
OUTPUT UPDATED ON
RPOS
RNEG
RDATA
Falling RCLK
LOW
SDO
Rising SCLK
RPOS
RNEG
RDATA
Rising RCLK
HIGH
SDO
Falling SCLK
相關PDF資料
PDF描述
DS2151QN IC TXRX T1 1-CH 5V LP IND 44PLCC
DS2152L+ IC TXRX T1 1CHIP ENHNCD 100-LQFP
DS2153Q-A7+T&R IC TXRX E1 1-CHIP 5V 44-PLCC
DS2154LNA2+ IC TXRX E1 5V 100-LQFP
DS2154L IC TXRX E1 1CHIP 5V ENH 100-LQFP
相關代理商/技術參數
參數描述
DS2149Q/T&R 制造商:Maxim Integrated Products 功能描述:5V T1/E1 LIU T&R COMM - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LINE INTERFACE 5V T1/E1 PLCC
DS2149Q/T&R+ 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel
DS2149Q/T&R 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2149Q+ 功能描述:網絡控制器與處理器 IC 5V T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2149Q+T&R 制造商:Maxim Integrated Products 功能描述:FRAMER J1/T1 5V 28PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LIU T1/J1 5V 28-PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*