參數資料
型號: DS21Q348N
廠商: Maxim Integrated Products
文件頁數: 19/76頁
文件大?。?/td> 0K
描述: IC LIU T1/E1/J1 QUAD 3.3V 144BGA
標準包裝: 90
類型: 線路接口裝置(LIU)
規程: E1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 144-BBGA
供應商設備封裝: 144-PBGA(17x17)
包裝: 管件
DS21348/DS21Q348
26 of 76
3.2 Parallel Port Operation
When using the parallel interface on the DS21348 (BIS1 = 0) the user has the option for either
multiplexed bus operation (BIS1 = 0, BIS0 = 0) or non-multiplexed bus operation (BIS1 = 0, BIS0 = 1).
The DS21348 can operate with either Intel or Motorola bus timing configurations. If the PBTS pin is tied
low, Intel timing will be selected; if tied high, Motorola timing will be selected. All Motorola bus signals
are listed in parentheses (). See the timing diagrams in Section 11 for more details.
3.3 Serial Port Operation
Setting BIS1 = 1 and BIS0 = 0 enables the serial bus interface on the DS21348. Port read/write timing is
unrelated to the system transmit and receive timing, allowing asynchronous reads or writes by the host.
See Section 11 for the AC timing of the serial port. All serial port accesses are LSB first. See Figure 3-1,
Reading or writing to the internal registers requires writing one address/command byte prior to
transferring register data. The first bit written (LSB) of the address/command byte specifies whether the
access is a read (1) or a write (0). The next 5 bits identify the register address. Bit 7 is reserved and must
be set to 0 for proper operation.
The last bit (MSB) of the address/command byte is the burst mode bit. When the burst bit is enabled
(B = 1) and a READ operation is performed, addresses 0 through 15h are read sequentially, starting at
address 0h. And when the burst bit is enabled and a WRITE operation is performed, addresses 0 through
16h are written sequentially, starting at address 0h. Burst operation is stopped once address 15h is read.
See Figure 3-5 and Figure 3-6 for more details.
All data transfers are initiated by driving the
CS input low. When Input Clock-Edge Select (ICES) is low,
input data is latched on the rising edge of SCLK and when ICES is high, input data is latched on the
falling edge of SCLK. When Output Clock-Edge Select (OCES) is low, data is output on the falling edge
of SCLK and when OCES is high, data is output on the rising edge of SCLK. Data is held until the next
falling or rising edge. All data transfers are terminated if the
CS input transitions high. Port control logic
is disabled and SDO is tri-stated when
CS is high.
相關PDF資料
PDF描述
MS3451L18-1SW CONN RCPT 10POS CBL MNT W/SCKT
D38999/26MH53SB CONN PLUG 53POS STRAIGHT W/SCKT
MS3451L18-1S CONN RCPT 10POS CBL MNT W/SCKT
D38999/24KA98HN CONN RCPT 3POS JAM NUT W/PINS
VE-B6Y-MX-S CONVERTER MOD DC/DC 3.3V 49.5W
相關代理商/技術參數
參數描述
DS21Q348NB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q348-W 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q352 功能描述:網絡控制器與處理器 IC 3.3/5V Quad T1/E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q352B 功能描述:網絡控制器與處理器 IC 3.3/5V Quad T1/E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q352B+ 功能描述:網絡控制器與處理器 IC 3.3/5V Quad T1/E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray