________________________________________________ DS33X162/X161/X82/X81/X42/X41/X11/W41/W11
Rev: 063008
24 of 375
PACKAGE PINS
NAME
256
144
TYPE
FUNCTION
TX_EN1,
TX_EN2
K14,
P16
F8
O
Transmit Enable 1(GMII). When this signal is asserted, the data on
TXD[7:0] is valid.
Transmit Enable 1, 2 (MII/RMII). In MII mode, this pin is asserted high
when data TXD[3:0] is being provided by the device. In RMII mode, this
pin is asserted high when data TXD[1:0] is being provided by the device.
The signal is deasserted prior to the first nibble of the next frame. This
signal is synchronous with the rising edge TX_CLK. It is asserted with the
first bit of the preamble.
Note that TX_EN2 is only available on devices with two Ethernet ports.
Unused output pins should not be connected.
RX_DV1,
RX_DV2
G15,
M11
F9
I
Receive Data Valid 1 (GMII). This signal is synchronous to the RX_CLK1
and provides a valid signal for the RXD[7:0].
Receive Data Valid 1, 2 (MII/RMII). This active-high signal indicates valid
data from the PHY. In MII mode the data RXD[3:0] is ignored if RX_DV is
not asserted high. In RMII mode the data RXD[1:0] is ignored if RX_DV is
not asserted high.
Note that RX_DV2 is only available on devices with two Ethernet ports.
RX_CRS1,
RX_CRS2
E13,
J14
G12
I
Receive Carrier Sense 1 (GMII). This signal is asserted (high) when data
is valid from the PHY. This signal is asserted by the PHY when either
transmit or receive medium is active. This signal is not synchronous to
any of the clocks.
Receive Carrier Sense 1, 2 (MII). This signal is asserted by the PHY when
either transmit or receive medium is active. This signal is not synchronous
to any of the clocks.
Note that RX_CRS2 is only available on devices with two Ethernet ports.
RX_ERR1,
RX_ERR2
H15,
M12
G9
I
Receive Error 1 (GMII). This signal indicates a receive error or a carrier
extension in the GMII Mode.
Receive Error 1, 2 (MII). Asserted by the MAC PHY for one or more
RX_CLK periods indicating that an error has occurred. Active High
indicates Receive code group is invalid. If RX_CRS is low, RX_ERR has
no effect. This is synchronous with RX_CLK. In DCE mode, this signal
must be grounded.
Note that RX_ERR2 is only available on devices with two Ethernet ports.
TX_ERR1,
TX_ERR2
L14,
R16
G8
O
Transmit Error 1(GMII). When this signal is asserted, the PHY will
respond by sending one or more code groups in error.
Transmit Error 1, 2(GMII, MII). When this signal is asserted, the PHY will
respond by sending one or more code groups in error.
Note that TX_ERR2 is only available on devices with two Ethernet ports.
COL1,
COL2
E14,
L16
G10
I
Collision Detect 1, 2 (MII). Asserted by the Ethernet PHY to indicate that
a collision is occurring. In DCE Mode this signal should be connected to
ground. This signal is only valid in half duplex mode, and is ignored in full
duplex mode.
Note that COL2 is only available on devices with two Ethernet ports.
DCEDTES
P13
L7
I
DCE or DTE Selection (MII). Setting this pin high places all Ethernet
ports in DCE Mode. Setting this pin low places the Ethernet ports in DTE
Mode.
In DCE Mode, the MII interface can be directly connected to another
MAC. In DCE Mode, the Transmit clock (TX_CLK) and Receive clock
(RX_CLK) are outputs.
Note that there is no software bit selection of DCEDTES. Note that DCE
operation is only valid for 10/100, MII mode.
RMII_SEL
M14
K7
I
RMII Selection Input. Set this pin to 1 for RMII operation. In devices with
2 Ethernet ports, both ports will operate in RMII mode. REF_CLK must be
50MHz. Set this pin to 0 for GMII or MII operation.