- 您現在的位置：買賣IC網 > PDF目錄16258 > DS33Z44DK (Maxim Integrated Products)KIT DESIGN FOR DS33Z44 PDF資料下載
參數資料
| 型號： | DS33Z44DK |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/59頁 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN FOR DS33Z44 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網 |
| 已用 IC / 零件： | DS33Z44 |
| 已供物品： | 板，2 個串行卡，CD |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
DS33Z44DK
12 of 59
Quick Setup #2 (DS3174 T3E3)
On the DS3174 serial resource card install jumper J24. Jumpers JP16–JP19 should be set high. This places
the card in DS3174 mode and enables all four ports as described in Table 3.
Complete the hardware configuration and one of the basic DS33Z44 configurations as previously described.
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Launch ChipView.exe (or use existing session if it is already open) and select Register View. When prompted
for a definition file, pick the file name ds3184_evbrd_reduced.def. After the definition file loads, go to the File
menu and select File→Memory Config File→Load .MFG file. When prompted, select the file named
84_t3_sct_needscoaxlb.mfg
.
Place a loopback connector at the DS3174 network side.
At this point, any packets sent to the DS33Z44 are echoed back. Incoming packets (i.e., ping) should cause the
RX LED to blink, after which the TX LED should also blink.
Quick Setup #3 (DS21458 T1E1)
Complete the hardware configuration and one of the basic DS33Z44 configurations as previously described.
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
Launch ChipView.exe (or use existing session if it is already open) and select Register View. When prompted
for a definition file, pick the file named DS21458.def. After the definition file loads, go to the File menu and
select File
→Reg Ini File→Load Ini File. When prompted, pick the file named
e1_gapclk_crc4_hdb3_nocas.ini
.
Place a loopback connector at the DS21458 network side; RLOS LED should go out.
At this point any packets sent to the DS33Z44 are echoed back. Incoming packets (i.e. ping) should cause the
RX LED to blink, after which the TX LED should also blink.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JWK-EZ-F3 | CONVERTER MOD DC/DC 40V 25W |
| RCC19DREH | CONN EDGECARD 38POS .100 EYELET |
| GBA32DRMI-S288 | CONN EDGECARD 64POS .125 EXTEND |
| EET-UQ2E122EA | CAP ALUM 1200UF 250V 20% SNAP |
| VE-JWK-EZ-F2 | CONVERTER MOD DC/DC 40V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS33ZH11 | 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33ZH11+ | 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS34 | 制造商:LUMILEDS 制造商全稱:LUMILEDS 功能描述:power light source Luxeon V Emitter |
| DS-3400D UK | 制造商:TRUST 功能描述:DESKTOP WIRELESS OPTICAL TRUST |
| DS3404FP000 | 制造商:Thomas & Betts 功能描述:30A,PLG,3P4W,MG,404,3P480V |
發布緊急采購，3分鐘左右您將得到回復。