- 您現在的位置：買賣IC網 > PDF目錄8541 > DS3911T+T (Maxim Integrated Products)IC DAC 10BIT I2C QUAD 14TDFN PDF資料下載
參數資料
| 型號： | DS3911T+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 10BIT I2C QUAD 14TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 4 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 1.74W |
| 工作溫度： | -40°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 14-TDFN-EP（3x5） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 4 電壓，單極 |
| 采樣率（每秒）： | * |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
DS3911
Temperature-Controlled, Nonvolatile,
I2C Quad DAC
11
Maxim Integrated
how a positive and negative tempco can be achieved by
adjusting DAC OFFSET values. The DACs are updated
after each temperature conversion.
ing if the measured temperature falls on the boundary
between two windows (Figure 5). This 1NC hysteresis is
implemented in the TINDEX register value calculation by
adding 1NC to temperature changes of negative slope.
Temperature Conversion and
Supply Voltage Monitoring
Temperature Conversion
The device features an internal 12-bit temperature sensor
that can drive the LUT and provide a measurement of the
ambient temperature over I2C by reading the value stored
in memory addresses 04h–05h. The sensor is functional
over the entire operating temperature range, and the results
are stored in signed two’s-complement format with a 1/16NC
resolution. See the Lower Memory, Register 04h–05h: TEMP
VALUE section for the temperature sensor’s bit weights. The
DONETEMP bit located in the CTRL register indicates
whether a temperature conversion has been completed
since the bit was last cleared.
Supply Voltage Monitoring
The device also features an internal 13-bit supply voltage
(VCC) monitor. A left-justified value of the supply voltage
measurement can be read over I2C at memory address-
es 06h–07h. To calculate the supply voltage, simply
convert the hexadecimal result into decimal and then
multiply it by the LSB as shown in the Analog Voltage
Monitoring Characteristics electrical specifications table.
The DONEVCC bit located in the CTRL register indicates
whether a VCC conversion has been completed since the
bit was last cleared.
Slave Address Byte and Address Pins
The slave address byte consists of a 7-bit slave address
plus a R/W bit, as shown in Figure 6. The device’s slave
address is determined by the state of the A0 and A1
address pins. These pins allow up to four devices to
reside on the same I2C bus. Address pins connected to
GND result in a 0 in the corresponding bit position in the
slave address. Conversely, address pins connected to
VCC result in a 1 in the corresponding bit positions. For
example, the device’s slave address byte is B0h when
A0 and A1 are grounded. See the I2C Serial Interface
section for more information.
I2C Serial Interface
I2C Definitions
The following terminology is commonly used to describe
the I2C AC Electrical Characteristics table for additional
information.
Master Device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses and START and STOP conditions.
Slave Devices: Slave devices send and receive data
at the master’s request.
Bus Idle or Not Busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states.
START Condition: A START condition is generated by
the master to initiate a new data transfer with a slave.
Transitioning SDA from high to low while SCL remains
high generates a START condition.
Figure 5. LUT Hysteresis
Figure 6. DS3911 Slave Address Byte
MEMORY
LOCATION
9D
DECREASING
TEMPERATURE
INCREASING
TEMPERATURE
1°C HYSTERESIS
WINDOW
TEMPERATURE (°C)
56
58
60
62
64
66
9C
9B
9A
99
98
10
1
1R/W
A0
A1
0
MSB
LSB
SLAVE ADDRESS*
*THE SLAVE ADDRESS IS DETERMINED BY ADDRESS PINS A0 AND A1.
READ/WRITE BIT
相關PDF資料 |
PDF描述 |
|---|---|
| LT6553CGN#TRPBF | IC AMP VIDEO TRIPLE GAIN2 16SSOP |
| VE-J4X-MW-S | CONVERTER MOD DC/DC 5.2V 100W |
| VE-B3F-MU-F4 | CONVERTER MOD DC/DC 72V 200W |
| LT6553CGN#TR | IC AMP VIDEO TRIPLE GAIN2 16SSOP |
| VE-J4V-MW-S | CONVERTER MOD DC/DC 5.8V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3920 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Fast Current Mirror |
| DS3920_1112 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Fast Current Mirror |
| DS3920T-001+ | 功能描述:電流和電力監控器、調節器 Fast APD Bias RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| DS3920T-001+T | 功能描述:電流和電力監控器、調節器 Fast APD Bias w/20mA limit RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| DS3920T-002+ | 功能描述:電流和電力監控器、調節器 Fast Current Mirror RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。